DP 6000 DIGITAL PAGING SYSTEM
INSTALLATION INSTRUCTION 83
February 1997
Page 12/29
The operation code can be programmed into the transceiver
by transmitting a paging system call (wireless via the system
transmitter or wired while the transceiver is stored in its stor-
age rack).
The transceiver programming switch in the battery compart-
ment should be set to the programming mode to make the
transceiver receptive for this system call.
The special programming call for the operation codes look as
follows:
CCC N P QRSTU
N = 6 for programming opcode 1 in the transceiver
N = 7 for programming opcode 2 in the transceiver
N = 8 for programming opcode 3 in the transceiver
N = 9 for programming opcode 4 in the transceiver
N = A for programming opcode 5 in the transceiver
N = B for programming opcode 6 in the transceiver
PQRSTU
=
6 digit operation code.
PROGRAMMING THE OPCODES VIA A PC FITTED
WITH THE LBB 6000 CARD:
-
Enter the ‘Edit’ menu in the user program
-
Select the ‘receiver’ menu item
-
Select ‘program opcodes’
-
Enter the ‘opcode’ number N as shown above
-
Enter the opcode: PQRSTU
PROGRAMMING THE OPCODES VIA THE LBB 5800
DESK SERIES
-
Press the PROGRAM key
-
Enter the opcode number N as shown above
-
Enter the opcode : PQRSTU
PROGRAMMING THE OPCODES VIA THE PROGRAM-
MING KEYBOARD OF TELEPHONE COUPLER LBB 5840
Operation code 1 , press C/CCC6/PQRSTU
Operation code 2 , press C/CCC7/PQRSTU
Operation code 3 , press C/CCC 8/PQRSTU
Operation code 4 , press C/CCC9/PQRSTU
Operation code 5 , press C/CCCA/PQRSTU
Operation code 6 , press C/CCCB/PQRSTU
3.2 USER FUNCTIONS
The transceiver user programming is fully menu driven and can
be accessed as follows:
■
Press the MENU key to enter the menu
■
Press the UP/DOWN keys to scroll through the menu
■
Activate the selected menu item by pressing the ENTER
key.
The menu is closed when no selection is made after 5 seconds.
All of the following functions can be enabled or disabled by
opcode programming. In this description it is assumed all user
programming options are enabled.
3.2.1 SWITCHING ON/OFF
To switch on the transceiver: Press the MENU key, the alpha
display shows: “POWER ON ?” Push the ENTER key within 5
seconds. When the transceiver is switched on, a short acoustic
signal is audible. The alphanumeric display shows the last
received message or “NO MESSAGE”. The numeric display
shows the first individual address.
In ‘new system mode’, the transceiver’s display shows “WAIT-
ING FOR CENTRAL” and after a handshake with the central
will switch on. If the the handshake fails, ‘CENTRAL NOT
RESPONDING’ is displayed after 20 seconds and the trans-
ceiver starts to bleep until the reset button is pressed. After
pressing the reset button, the transceiver switches off.
A hard override is possible by pressing the button sequence
UP/DOWN/LIGHT.
WARNING:
The hard override is not detected by the
paging system. Using the hard override can cause conflicts
in the status of the system.
To switch off the transceiver: press the MENU key, scroll
down the menu until “POWER OFF?” is displayed and press
the ENTER key When the transceiver is switched off, a long
acoustic signal is audible.
In ‘new system mode’, the transceiver’s display shows “WAIT-
ING FOR CENTRAL” and after a handshake with the central
the transceiver switches OFF. If the the handshake fails, ‘CEN-
TRAL NOT RESPONDING’ is displayed after 20 seconds and
the transceiver starts to bleep until the reset button is pressed.
After pressing the reset button, the transceiver remains on.
The alphanumeric display shows the last received message or
“NO MESSAGE”.
A hard override is possible by pressing the button sequence
UP/DOWN/LIGHT.
WARNING: The hard override is not detected by the pag-
ing system. Using the hard override can cause conflicts in
the status of the system.
