9
8
1. Press and hold
SETUP
until the indicator remains on,
then release
SETUP
.
2. Repeatedly press
SELECT
to select the desired
mode (
TV, VCR,
etc.), unless the desired mode is
already selected.
3. Enter the 4-digit code from the code tables (on
separate sheet).
Note:
After a valid code entry, the
indicator turns off. For an invalid code, the indicator
flashes.
4. Press
CHANNEL UP
. If the device responds, no further
programming is required.
Note:
If some buttons do not
operate your equipment, try one of the other codes for
your brand.
If your product does not respond after you have tried all
the codes for your brand or if your brand is not listed,
try searching for your code by following these steps.
1. Turn on the device (
TV
,
VCR
, etc.) to be controlled.
2. Press and hold
SETUP
until the indicator remains
on, then release
SETUP
.
3. Repeatedly press
SELECT
to select the desired
mode (
TV, VCR,
etc.), unless the desired mode is
already selected.
4. Press
CHANNEL UP
repeatedly (up to 300 times)
until the device to be controlled changes channels.
The indicator blinks off with each button press.
5. Press and release
MUTE
to install the code.
Most users store VCR codes under
VCR
. Cable codes
appear under
CBL
(Cable), etc.
If you want to store a VCR code under
CBL
, first follow
the procedure for Direct Code Entry and select
CBL
in
Step 2 of Direct Code Entry. Then enter any VCR code in
Step 3 of Direct Code Entry. Then follow the steps above
for Code Search.
Note
: If the device does not have a
CHANNEL UP
button, use
PLAY
(VCR only) or
POWER
instead.
Code search begins from the currently stored 4-digit
number under that mode.
The Code Identification Feature lets you identify the 4-
digit library code stored under your device key.
If you want to find what 4-digit code is stored under any
device mode, follow these steps.
1. Press and hold
SETUP
until the indicator remains on,
then release
SETUP
.
2. Repeatedly press
SELECT
to select the desired
mode (
TV, VCR,
etc.), unless the desired mode is
already selected.
3. Press and release
SETUP
. The indicator blinks.
4. To find the first digit for the code stored under the
mode selected in Step 2, press each number button
(0
-
9)
. When the indicator blinks off, the number you
pressed is the first code digit you are searching for.
5. To find the second digit, repeat Step 4. When the
indicator blinks off, this is the second digit.
6. Repeat Step 4 to find the third and fourth digits.
Lets you search for a code for a specific Brand within
the Code Library for a particular manufacturer.
1. Turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold
SETUP
until the indicator remains on,
then release
SETUP
.
3. Repeatedly press
SELECT
to select the desired
mode (
TV, VCR,
etc.), unless the desired mode is
already selected.
4. Press and release the numeric button (
0-9
)
corresponding to desired Manufacturer (see table
on code list sheet). The green indicator blinks off
once. Note, pressing “0” performs a full library
search same as normal Code Search Method on
previous page.
5. Press the
CHANNEL UP
button ((or
POWER
or
PLAY
(VCR only)) repeatedly until the device to be
controlled changes channel. The green indicator
blinks off with each button press. If you accidentally
overshoot the code required, press the
CHANNEL
DOWN
button to backtrack through the library until
the device changes channel. Pressing
CHANNEL
UP
changes direction to forward again.
6. Press and release
MUTE
to install the code.
Brand Search Method entry is now complete.
Note
: When all codes under a Brand have been
searched the indicator flashes rapidly for 3 seconds.
Direct Code Entry
Code Search
Code Search by Brand
Code Identification Feature
