English
38
Clock/Timer Operations
Viewing the clock
The clock (if it is set) will be shown in standby
mode.
To view the clock in any source mode
(DISC or TUNER) for example:
1
Press
CLOCK
on the system.
➜
The clock is displayed for a few seconds.
➜
If the clock has not been set, "
NO CLOCK
" is
displayed for a few seconds.
Setting the clock
1
In standby mode, press and hold
CLOCK
on
the system.
➜
The clock digits flash on the display panel.
➜
If the clock has not been set, "--:--" flashes
2
Press
PRESET
O
/
P
repeatedly to set the
hour.
3
Press
SEARCH•TUNING
1
/
¡
repeatedly to set the minute.
4
Press
DISPLAY/OSD
repeatedly to switch to
between 12-hour and 24-hour display.
5
Press
CLOCK
again to store the setting.
➜
The clock starts working.
Notes:
– The clock setting will be erased when the
system is disconnected from the power supply.
– The system will exit clock setting mode if no
button is pressed within 10 seconds.
– To exit clock setting without storing, press
9
on
the system to exit.
Setting the wake-up timer
The system can switch on to DISC, USB or
TUNER mode automatically at a preset time,
serving as an alarm to wake you up.
Important!
– Before setting the timer, ensure that
the clock is set correctly.
– To set a new timer, you need to
deactivate the previously set timer.
1
In standby mode, press and hold
TIMER/
SLEEP
on the remote for more than five
seconds to enter timer setting mode.
➜
The source and timer digits will be light on
the display panel.
2
Press
DISC1/2/3
,
USB
or
TUNER
to select
the desired source.
●
Before setting timer, make sure the music source
has been prepared.
DISC1/2/3
– load the disc(s).
USB
– inser t a USB driver.
TUNER
– tune to the desired radio station.
3
Press
PRESET
O
/
P
repeatedly to set the
hour.
4
Press
SEARCH•TUNING
1
/
¡
repeatedly to set the minute.
5
Press
TIMER/SLEEP
to store the time.
●
At the preset time, the selected source will be
played.
Viewing the timer
1
In standby mode, press
TIMER/SLEEP
to view
timer (e.g “
DISC 03
:
03
“), Timer will be shown
on the display for a few seconds and then go
back to it’s previous status.
2
If timer have not been set, “
TIMER OFF
” will
be displayed for a few seconds.
To deactivate the wake-up timer
●
In standby mode, press
TIMER/SLEEP
to the
view timer mode, then press
9
until “
TIMER
OFF
“ is displayed on the panel. ( press
9
again
to switch to “
TIMER ON
“ )
Notes:
– The system will exit timer setting mode if no
button is pressed within 10 seconds.
– Display shows if timer is activated, and
disappears if it is inactivated.
Setting the sleep timer
The sleep timer enables the system to switch off
by itself after a set period of time.
1
Press
TIMER/SLEEP
on the remote control
repeatedly to select a preset time.
➜
The selections are as follows (time in
minutes):
15
➜
30
➜
45
➜
60
➜
90
➜
120
➜
OFF
2
Press
TIMER/SLEEP
until you reach the
desired length of time.
To deactivate the sleep timer
●
Press
TIMER/SLEEP
repeatedly until "OFF" is
displayed, or press
B
.
FWD397-98_UM ENG_0514
2008.5.14, 15:53
38
