manualshive.com logo in svg

Philips EasyAir SNS210 MC, Design-In Manual

Share
Download
Philips EasyAir SNS210 MC Design-In Manual Download Page 17

1

7

Design-in Guide - EasyAir SNS210

 MC

August

 202

1

When a group of luminaires is in the same daylight
condition and needs to be operated at the same level, it is
possible to use one sensor to control multiple luminaires.
This can be done in two ways:
(a) Use an SR bridge which can then connect to multiple
DALI drivers. For details on SR bridge, please refer to
design in guide of SR bridge.
(b) add multiple SR drivers together.

In case EasyAir SNS210 MC

, SNS410 MC

 is connected to 

multiple Philips

 

Xitanium SR LED drivers, the number of 

drivers is limited to

 

10.

 

Not more than 4 drivers should 

have DALI power

 

supply enabled. To minimize unnecessary 

losses, it is

 

recommended to turn on only two DALI power 

supplies.

 

Each SR driver provides approximately 55mA of 

current on

 

the DALI bus, and EasyAir SNS210 MC is limited 

to 250mA.

EasyAir SNS210 MC

, SNS410 MC

 sends commands to all 

connected

 

drivers (using broadcast command); it does not 

have

 

capabilities to address individual drivers. The light

 

commands are sent as a broadcast command, so

 

occupancy-/daylight-based lighting control and task

 

tuning operate the same on all connected drivers. The

 

readout of energy information from the connected drivers

 

will not function. The energy readout of multiple drivers is

 

foreseen in our roadmap.

Warning:

Please note the DALI power supply can only be
turned on/off on the Philips Xitanium SR LED
driver through the MultiOne tool. For this
application, please also make sure all drivers that
are connected to the sensor have the same wiring
polarity. SR drivers are shipped with the power
supply on as default.

i

EasyAir SNS210 MC

, SNS410 MC

 with multiple 

Philips Xitanium SR LED drivers (1:N application)

EASYAIR

DA
DA

Enable DALI PS

LED+
LED+

LED-

LED-

RSET2
SGND

NFC ANTENNA

DA

-

Connectors 

DA

+

LINE

NEUTRAL

GROUND

NC

Enable DALI PS

LED+
LED+

LED-

LED-

RSET2
SGND

NFC ANTENNA

DA

-

Connectors 

DA

+

LINE

NEUTRAL

GROUND

NC

Enable DALI PS

LED+
LED+

LED-

LED-

RSET2
SGND

NFC ANTENNA

DA

-

Connectors 

DA

+

LINE

NEUTRAL

GROUND

NC

Enable DALI PS

LED+
LED+

LED-

LED-

RSET2
SGND

NFC ANTENNA

DA

-

Connectors 

DA

+

LINE

NEUTRAL

GROUND

NC

Summary of Contents for EasyAir SNS210 MC
























Reviews:

No comments

Brands by name

Popular brands

Load more brands