ANSI
Std.
Rated Approx.
Approx.
Product
Ordering
Nom.
Code/
Pkg.
LCL
MOL
Avg. Life
Initial
Mean
CCT
Number
Code
Watts
Bulb
Base
Ballast Ref.
Qty.
Description
(In.)
(In.)
Hrs.
1
Lumens
2
Lumens
3
CRI
(K)
13093-0
CDM250S50/V/O/4K/ALTO
250
ED-18
Mog.
M168/O
12
G, Clear,Vertical ±15º (4, 5, 6)
5
3
⁄
4
9
3
⁄
4
20,000
22,500
19,125
85
4000
13094-8
CDM400S51/V/O/4K/ALTO
400
ED-18
Mog.
M169/O
12
G, Clear,Vertical ±15º (4, 5, 6)
5
3
⁄
4
9
3
⁄
4
20,000
34,000
28,900
85
4000
Electrical,Technical and Ordering Data
(Subject to change without notice)
MasterColor
®
Ceramic Metal Halide HPS-Retro White
™
◗
MasterColor technology optimized to operate in existing HPS fixtures,
which means a simple, twist-of-the-wrist conversion
◗
Improved work environment (crisp white light vs. yellow light)
◗
Better for the environment:TCLP
•
-compliant
◗
Replace yellow light with white light with just a simple twist!
◗
For operation on HPS ballasts; 85% lumen maintenance
◗
No shut off required in 24-hour-a-day/7-day-a-week operations
(relamp fixtures at or before the end of rated life)
Warnings, Cautions and Operating Instructions
R
“WARNING:
These lamps can cause serious skin
burn and eye inflammation from short wave ultraviolet
radiation if outer envelope of the lamp is broken or
punctured. Do not use where people will remain for more
than a few minutes unless adequate shielding or other safety
precautions are used. Certain lamps that will automatically
extinguish when the outer envelope is broken or punctured
are commercially available.”This lamp complies with FDA
radiation performance standard 21 CFR subchapter J.
(USA:21CFR 1040.30 Canada:SOR/DORS/80-381)
If the outer bulb is broken or punctured, turn off
at once and replace the lamp to avoid possible
injury from hazardous short wave ultraviolet
radiation. Do not scratch the outer bulb or subject
it to pressure as this could cause the outer bulb to
crack or shatter. A partial vacuum in the outer
bulb may cause glass to fly if the envelope is struck.
WARNING:
The arc-tube of metal halide lamps
are designed to operate under high pressure and at
temperatures up to 1000º C and can unexpectedly rupture
due to internal or external factors such as a ballast failure or
misapplication. If the arc-tube ruptures for any reason, the
outer bulb may break and pieces of extremely hot glass
might be discharged into the surrounding environment. If
such a rupture were to happen,
THERE IS A RISK OF
PERSONAL INJURY, PROPERTY DAMAGE,
BURNS AND FIRE.
These lamps are designed to retain all the glass
particles should an arc tube rupture occur.The
following operating instructions are recommended
to minimize these occurrences.
RELAMP FIXTURES AT OR BEFORE THE END OF
RATED LIFE.Allowing lamps to operate until they
fail is not advised and may increase the possibility of
inner arc tube rupture.
This lamp contains an arc tube with a filling gas
containing Kr-85 and is distributed by Philips
Lighting Company, a division of Philips Electronics
North America Corporation, Somerset, New
Jersey, 08875.
CAUTION:
TO REDUCE THE RISK OF PERSONAL
INJURY, PROPERTY DAMAGE, BURNS AND FIRE
RESULTING FROM AN ARC-TUBE RUPTURE THE
FOLLOWING
LAMP OPERATING INSTRUCTIONS
MUST BE FOLLOWED:
LAMP OPERATING INSTRUCTIONS:
1. RELAMP FIXTURES AT OR BEFORE THE END OF
RATED LIFE. Allowing lamps to operate until they fail is
not advised and may increase the possibility of inner arc
tube rupture.
2. Before lamp installation/replacement, shut power off and
allow lamp and fixture to cool to avoid electrical shock
and potential burn hazards.
3. Use only auxiliary equipment meeting Philips and/or
ANSI standards. Use within voltage limits recommended
by ballast manufacturer.
A. Operate lamp only within specified limits of operation.
B. For total supply load refer to ballast manufacturers
electrical data.
4. Periodically inspect the outer envelope. Replace any
lamps that show scratches, cracks or damage.
5. If a lamp bulb support is used, be sure to insulate the
support electrically to avoid possible decomposition of
the bulb glass.
6. Protect lamp base, socket and wiring against moisture,
corrosive atmospheres and excessive heat.
7.Time should be allowed for lamps to stabilize in color
when turned on for the first time.This may require
several hours of operation, with more than one start.
Lamp color is also subject to change under conditions
of excess vibration or shock and color appearance may
vary between individual lamps.
8. Lamps may require 10 to 20 minutes to re-light if there
is a power interruption.
9.Take care in handling and disposing of lamps. If an arc
tube is broken, avoid skin contact with any of the
contents or fragments.
WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS for Protected MasterColor
®
Ceramic Metal Halide
HPS-Retro White
™
Lamps ED-18 (Vertical Burn ± 15º, Open or Enclosed Fixtures)
1) Rated average life is the life obtained, on the average,
from large representative groups of lamps in laboratory
tests under controlled conditions at 10 or more operat-
ing hours per start. It is based on survival of at least 50%
of the lamps and allows for individual lamps or groups of
lamps to vary considerably from the average.
2) Approximate lumen values listed are for vertical
operation of the lamp.
3) Approximate lumen output at 40% of lamp rated average life.
4) Performance may not be satisfactory unless operated
within specified operating positions.
5) Heat resisting glass bulb.
6) MasterColor
®
Metal Halide Lamps are not recommended
for use on dimmers and are not warranted if used on
dimmer systems.
This product utilizes ALTO
®
Lamp Technology. ALTO
products pass the US EPA's Toxicity Characteristic Leaching
Procedure (TCLP) for non-hazardous waste status.
FOOTNOTES for MasterColor
®
Ceramic Metal Halide HPS-Retro White
®
Lamps
Philips Lighting Company
200 Franklin Square Drive
P.O. Box 6800
Somerset, NJ 08875-6800
1-800-555-0050
A Division of Philips Electronics North America Corporation
Updated 8/04
P-2220-E
Philips Lighting
281 Hillmount Road
Markham, Ontario
Canada L6C 2S3
1-800-555-0050
A Division of Philips Electronics Ltd.
www.philips.com
