Philips 7.5ft Lighted Balsam Fir Quick Start Manual Download Page 8 | Manualshive

Page: 8 / 16

background image

SAVE THESE INSTRUCTIONS

Item #755712, 758775

051 01 2039, 051 01 3039

Page 1 of 2

Quick Start Guide

7.5

’ Lighted Balsam Fir

What’s in the box

Tree Top (A)

Tree Middle

Section(B)

Tree Bottom

Section(C)

Tree Stand

(D)

What’s next



Read enclosed Safety and User Instructions, all Warnings, and Assembly Instruction manuals
before starting.



Select the area of your home where you will place your tree which should not be near fireplaces or
other sources of heat, and should be free from obstructions that prevent the installation of the tree.
The floor in this area must be flat to prevent the tree from tilting and wobbling and possibly falling
over.



Remove the parts of the tree and tree stand from the box by placing on a clean area of floor.



Remove the plastic pole protectors from the end of each tree section and discard.



To assemble the tree stand (D), slide the locking disk downward and snap into place

(see Fig 1).



Assemble the sections of the tree starting at the bottom and connect the light strings in each tree
section (light string connectors are shown in

Fig 2

). Note, the connectors have a polarity tab that must

line up when making connections. Secure the connector by tightening the ring on the connector.



Unpack the control box from its packaging inside the tree box and connect to the bottom section.



If a section of the tree does not light, check that all connectors are properly connected and see the
troubleshooting section in the Assembly Instructions for more information. More assembly
information and tree shaping tips are located in the Assembly Instructions manual.



Plug the cord from control box into a 110V-125V wall receptacle for lights to turn on.



Download the Illuminate

TM

app and install on your smartphone or tablet to control the Illuminate

TM

tree.

Follow the instructions on the next page to download and use the app.

Control Box (E)

2 Spare

Fuses (F)

Safety & User

Instruction

Sheet

Quick Start

Guide

Assembly

Instructions

4 Washers

(G)

2 Hinge

Pins

(H)

Fig. 1

Illuminate Password: 12345678

QR Codes to download App:
iOS/Apple

Android

«
...
6
7
8
9
10
...
»

Summary of Contents for 7.5ft Lighted Balsam Fir

















Reviews:

No comments

Related manuals for 7.5ft Lighted Balsam Fir

Brand: Santa's best Pages: 4

Brand: Santa's best Pages: 4

RGB LED Bluetooth Amplifier Christmas Tree DIY Kit

Brand: ICStation Pages: 17

Brand: hayneedle Pages: 4

Pre-lit Aspen Tree

Brand: EZ CONNECT Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands