Alignments
6.
This group setting of colour temperature will be applied
automatically to the TV / VGA / HDMI / AV sources.
6.4
Option Settings
6.4.1
Introduction
The microprocessor communicates with a large number of I
2
C
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
MT5580 ICs is made known by the option codes.
Notes:
•
After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE and press OK on the RC.
•
The new option setting is only active after the TV is
switched “off” / “stand-by” and “on” again with the mains
switch (the NVM is then read again).
6.4.2
Option Code Overview
Enter SAM mode to check the option codes. they could be
edited in the NVM.
6.4.3
Display Code Overview
Press the following key sequence on a standard RC
transmitter: “062598” directly followed by MENU and “xxx”,
where “xxx” is a 3 digit decimal value of the panel type: see
column “Display Code” in
. After resetting the Display
Code, restart the set immediately.
Table 6-3 Display code overview
6.5
Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
“00PF0000000000” and Production code “00000000000000”.
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool or use the “NVM editor” and “Dealer options”
items in SAM (do not forget to “store”).
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this, you can use the NVM editor in SAM. The loading of the
CTN and production code can also be done via ComPair
(Model number programming).
In case of a display replacement, reset the “Operation hours
display” to “0”, or to the operation hours of the replacement
display.
Remark:
- After the NVM has been replaced, go to SAM and scroll to the
<Reload MAC address> (see figure 1*).
- Select the item and press <OK> on the RC.
Warm (6500K)
32PFG5509/78
128
128
122
32PHG5509/78 125
115
128
40PFG5509/78
231
255
216
40PFG6309/78
239
220
241
42PFG5909/78
231
236
255
42PFG6519/78
236
255
246
42PFG6809/78
235
253
255
47PFG5909/78
218
229
255
47PFG6519/78
255
246
251
47PFG6809/78
255
255
136
48PFG5509/78
243
227
255
48PFG6309/78
235
196
255
55PFG6519/78
240
210
255
55PFG6809/78
255
251
252
CTN_ALT BOM#
Panel Type
Display Code
32PFG5509/78
TPT315B5-EUJFFA
098
32PHG5509/78
TPT315B5-DXJSFE
097
40PFG5509/78
TPT400LA-HM06
092
40PFG6309/78
TPT400LA-HF05
090
42PFG5909/78
TPT420H2-DUJSGE
091
42PFG6519/78
TPT420H2-DUJSGK 3S1B
089
42PFG6809/78
TPT420H2-DUJSGK 3S1A
088
47PFG5909/78
TPT470H1-DUJSGE
087
47PFG6519/78
TPT470H1-DUJSGK 3S1B
085
47PFG6809/78
TPT470H1-DUJSGK 3S1A
084
48PFG5509/78
TPT480LS-HN03
100
48PFG6309/78
TPT480LS-HJ02
086
55PFG6519/78
TPT550J1-DUJSGK S1C
099
55PFG6809/78
TPT550J1-DUJSGK S1B
102
Picture mode
Screen size
Colour temperature
Red
Green
Blue
