Philips 192E1SB/00 Service Manual Download Page 79

Page: 79 / 92

Meridian 1

3.10 Data for EDID & INF file

Data for EDID & .inf file

1 User visible strings on .inf file

Philips 192E1(19inch WIDE LCD MONITOR 192E1)

2 Manufacturer ID ( EDID data)

PHL

Product ID, "xxxx" 4 codes

MSB(byte 12): C0

LSB (byte 11): 2A

4 maximum

resolution

1366x768

5 Horizontal Frequency Range

30~83 KHz

6 Vertical Frequency Range

56~76Hz

7 Monitor Name (13 characterizes max.)

Philips 192E1

3.11 Hot-key definition

Item

Key

Key press time

OSD Timeout

OSD Message

Monitor Controls
Lock

[Menu]

6 sec

5 sec

Monitor controls locked
Monitor controls
unlocked (default)

Factory Mode

[AUTO]+[Menu]+[Power]

DDC/CI On/OFF
for VISTA

[MENU]+[DOWN]

5 sec

DDC/CI ON (default)
DDC/CI OFF

Any deviation between document and sample, please refer to Philips approved sample.

4 Visual

characteristics

4.1 Test conditions

Unless otherwise specified, this specification is defined under the following conditions.

(1) Input signal:

As defined in 3.3, 1366*768

non-interlaced mode (1366*768@60Hz 146.25MHz), signal sources must

have 75 ohm output impedance

(2) Luminance setting:

controls to be set to 300 nits with full screen 100 % duty cycle white signal

(3) Warm up:

More than 30 minutes after power on with signal supplied.

(4) Ambient light:

400 -- 600 lux

(5) Ambient temperature:

20 ± 5

4.2 Brightness

To follow Panel specification

4.3 Image size

Actual display size: Refer to

2.1

LCD PANEL spec.

4.4 Brightness uniformity

Set contrast at 100% and turn the brightness to get average above 300 nits at centre of the screen. Apply the Fig 1;

it should comply with the following formula:

B_min

100%

75%

(Follow

panel

spec)

B_max

Where B_max =Maximum brightness

B_min = Minimum brightness

Summary of Contents for 192E1SB/00





























































































Search results

Summary of Contents for 192E1SB/00

Reviews:

Related manuals for 192E1SB/00

Brands by name

Popular brands

Philips 192E1SB/00, Service Manual

Search results

Summary of Contents for 192E1SB/00

Reviews:

Related manuals for 192E1SB/00

Brands by name

Popular brands