Philips 150B6CB/00 Page 17 Service Manual Download | Manualshive

Page: 17 / 110

background image

17

Go to cover page

170B6 LCD

Electrical Instructions

1. General points

1.1 During the test and measuring, supply a distortion free AC mains

voltage to the apparatus via an isolated transformer with low internal
resistance.

1.2 All measurements mentioned hereafter are carried out at a normal

mains voltage (90 - 132 VAC for USA version, 195 -264 VAC for EU
ROPEAN version, or 90 - 264 VAC for the model with full range
power supply, unless otherwise stated.)

1.3 All voltages are to be measured or applied with respect to ground,

unless otherwise stated.
Note: don‘t use heat sink as ground.

1.4 The test has to be done on a complete set including LCD panel

after 30 minutes warm-up at least in a room with temperature of
25 +/- 5 degree C.

1.5 All values mentioned in these test instruction are only applicable of

a well-aligned apparatus, with correct signal.

1.6 The letters symbols (B) and (S) placed behind the test instruction

denotes

(B): carried out 100% inspection at assembly line
(S): carried out test by sampling

1.7 The white balance (color temperature) has to be tested in subdued

lighted room.

1.8 Repetitive power on / off cycle are allowed except it should be avoided

within 6 sec.

2.

Input signal

2.1 Signal type

2.1.1Video signal input

Signal source: pattern generator format as attachment (Table 1 to 34)

Reference generator: QuantumData 802BTThe input signals can be

applied in two different modes:

1). VESA Analog

The video input consists of red, green, and blue signals. The video

signals are analog levels, where 0V corresponds to black and

700mV is the maximum signal amplitude. Input impedance of video

pins is 75 ohm +/- 1%.

2). Intel DVI Digital

Input signal: Single TMDS link (Three channels: RX0-/+, RX1-/+,

RX2-/+).

2.1.2 Sync signal input

The capability of sync signal inputs shall include separate sync,

composite sync and sync on green. Input impedance: 2k2 ohms.

The signals are defined as follow:

Separate sync

TTL level, Positive/Negative

Composite sync

TTL level, Positive/Negative

Sync on green H-sync

TTL level, Positive/Negative

Signal source: pattern generator format as attachment (Table 1 to 34)

Reference generator: QuantumData 802BT

2.2

Input signal mode

The maximum resolution display of this monitor is up to 1280x1024,
SXGA signal input with full screen display. It shall also automatically
up-scale the lower resolution video modes into 1280x1024 full
screen display. The display capabilities shall include the following
timing modes:

(1) Preset modes (34 modes)

#

Resolution

H-Frequency

Pixel rate

V-Frequency

Comment

1

640X350

31.5K

25.175

70Hz

IBM VGA 10h

2

720X400

31.5K

28.322

70Hz

IBM VGA 3h

3

640X480

31.5K

25.175

60Hz

4

640X480

35.0K

30.24

67Hz

5

640X480

37.9K

31.5

72Hz

6

640X480

37.5K

31.501

75Hz

7

640X480

43.3K

36

85Hz

8

800X600

35.2K

36

56Hz

9

800X600

37.9K

40

60Hz

10

800X600

48.1K

50

72Hz

11

800X600

46.9K

49.498

75Hz

12

800X600

53.7K

56.251

85Hz

13

832X624

49.7K/

57.28

75Hz

MAC

14

1024X768

48.4K

65

60Hz

15

1024X768

56.5K

75

70Hz

16

1024X768

60.0K

78.75

75Hz

17

1024X768

61.1K

83.096

76Hz

IBM XGA-2

18

1024X768

68.7K

94.5

85Hz

19

1152X864

54.0K

79.9

60Hz

Non-VESA

20

1152X864

63.9K

94.5

70Hz

Non-VESA

21

1152X864

67.5K

108

75Hz

22

1152X870

68.7K

100

75Hz

MAC

23

1152X900

61.8K

92.94

66Hz

SUN Mode IV

24

1152X900

71.8K

108

76Hz

SUN Mode II

25

1280X960

60.0K

108

60Hz

26

1280X960

75.0K

129.895

75Hz

Non-VESA

27

1280X1024

64.0K

108

60Hz

28

1280X1024

71.7K

117

67Hz

SUN Mode V

29

1280X1024

76.0K

130.223

72Hz

DOS/V

30

1280X1024

80.0K

135

75Hz

31

1280X1024

81.1K

135.008

76Hz

SUN Mode I

32

688X556

31.3K

27

50Hz

TV-PAL

33

960X720

44.76K

57.58

60Hz

34

960X720

56.4K

72.42

75Hz

(2) Factory Preset modes (15 modes)

«
...
15
16
17
18
19
...
»

Summary of Contents for 150B6CB/00















































































































Reviews:

No comments

Related manuals for 150B6CB/00

Brand: Raymarine Pages: 18

Brand: NEC Pages: 26

Brand: Samsung Pages: 2

Brand: Raymarine Pages: 12

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 148

Brand: Sceptre Pages: 32

Brand: ItsImagical Pages: 16

Brand: ViewSonic Pages: 33

Brand: I-Tech Pages: 19

Brand: Gateway Pages: 30

Brand: BenQ Pages: 31

Brand: 4D systems Pages: 6

HANNS-G HL247HGB

Brand: HANNspree Pages: 23

Brand: Elecrow Pages: 6

Brand: Feit Electric Pages: 7

VG2227WM - 22" LCD Monitor

Brand: ViewSonic Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands