manualshive.com logo in svg

Philio PHI PST02-1C, Quick Start Manual

Share
Download
Philio PHI PST02-1C Quick Start Manual Download Page 2

06-10-2020 15

:

11

Pagina 2 van 9

http://manual.zwave.eu/backend/make.php?lang=en&sku=PHI_PST02-1C

send temperature and brightness value.

Features:

Contact sensor monitors door and window status (open/closed)

Measures and reports additional values for temperature and brightness

Tamper protection

Can be mounted on every planar surface in vertical or horizontal position

Firmware update „Over The Air“ (OTA)

Power Supply: Batterie (1x CR123A)

Wireless Technology: Z-Wave Plus

Dimensions: 28 x 95 x 35 mm

 

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it 

must be in factory default state.

 Please make sure to reset the device into factory default. You ca

by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommend
the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inope

1.  Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4th pressed, and the LED will light ON.
2.  After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise

will flash once. 

3.  IDs are excluded and all settings will reset to factory default.

.

Safety Warning for Batteries

The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different brands.

Installation

Battery Installation

When the device report the low battery message. The user should replace the battery to new one. The battery type is CR123A, 3.0V. The way to open the f
please follow below steps. 

Using a tool to press the 1-1 position, to release the cover.

Hold the front cover and pull back

Hold the front cover and pull up

Summary of Contents for PHI PST02-1C










Reviews:

No comments

Brands by name

Popular brands

Load more brands