manualshive.com logo in svg

Philio PHI PAN06, Quick Start, Page: 4 / 5

Share
Download
Philio PHI PAN06 Quick Start Download Page 4

6-7-2020

manual.zwave.eu/backend/make.php?lang=en&sku=PHI_PAN06

manual.zwave.eu/backend/make.php?lang=en&sku=PHI_PAN06

4/5

Setting

Description

0

Switch off

1

ignore

2

Switch toggle

3

Switch on

Parameter 6: Existence of Endpoint3

The endpoint3 of Multi-Channel Command Class is related to relay1 and relay2. It may be redundant for the need to control relay1 or relay2 individually. When

the Existence of Endpoint3 is set as 0, the endpoint3 of Multi-Channel Command Class will be disabled. 

Size: 1 Byte, Default Value: 1

Setting

Description

1

Endpoint3 exist

2

No Endpoint3

Technical Data

Dimensions

0.0470000x0.0390000x0.0160000 mm

Weight

40 gr

Hardware Platform

SD3502

EAN

4713698571160

IP Class

IP 20

Voltage

230 Der Endpunkt3 der Mehrkanal-Befehlsklasse bezieht sich auf Relais1 und Relais2. Es kann überflüssig

sein, die Notwendigkeit, Relais1 oder Relais2 einzeln zu steuern. Wenn die Existenz von Endpunkt3 als 0

gesetzt ist, wird der Endpunkt3 der Mehrkanal-Befehlsklasse deaktiviert.

Load

2x 1500W

Device Type

On/Off Power Switch

Generic Device Class

Binary Switch

Specific Device Class

Binary Power Switch

Firmware Version

01.08

Z-Wave Version

03.5f

Certification ID

ZC10-14120009

Z-Wave Product Id

0x013c.0x0001.0x0013

Frequency

Europe - 868,4 Mhz

Maximum transmission power

5 mW

Supported Command Classes

Basic
Switch Binary
Switch All
Scene Activation
Scene Actuator Conf
Association Grp Info
Device Reset Locally
Zwaveplus Info
Multi Channel
Configuration
Alarm
Manufacturer Specific
Powerlevel

Summary of Contents for PHI PAN06






Reviews:

No comments