manualshive.com logo in svg

Philio PHI PAN06, Quick Start, Page: 2 / 5

Share
Download
Philio PHI PAN06 Quick Start Download Page 2

6-7-2020

manual.zwave.eu/backend/make.php?lang=en&sku=PHI_PAN06

manual.zwave.eu/backend/make.php?lang=en&sku=PHI_PAN06

2/5

Put the in wall switch into a wall box and connect the pins as shown in the figure.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be 

added to an existing wireless network

 to communicate with the

devices of this network. This process is called 

Inclusion

.

Devices can also be removed from a network. This process is called 

Exclusion

. Both processes are initiated by the primary controller of the Z-Wave network. This

controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

Tripple Click the button on the device confirms inclusion. After power up it will stay in auto inclusion mode for 4 minutes. To support handling of the device when

already installed the external switch can be used for inclusion or exclusion for 3 minutes after power up.

Exclusion

Tripple Click the button on the device confirms exclusion. 

Product Usage

Manual Operation

The device can be operated using the externally connected switch. Three different modes are supported:

Edge Mode:

 Die Position of the external switch determines the switching state of the relay. After a wireless switching command it may be needed to operate

the switch twice to return to the direct relation of switch position and relay state. This mode is the factory default mode.

Toogle Mode:

 Each "ON"-Position of the external switch will toggle the state of the relays. This mode is particularly suited for mono-stable switches.

Edge/Toggle-Mode:

 Every change of the state of the external switch results in a change of the relay state.

Remote Operation

Remote On/Off control of the switch is possible with any Z-Wave controller. Further you can set associations to let your device controlled by other Z-Wave devices

like sensors.

Node Information Frame

The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The

inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send

out a Node Information Frame. To issue a NIF execute the following action: Tripple Click the button on the device sends out a Node Information Frame.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

Summary of Contents for PHI PAN06






Reviews:

No comments