background image

2-2-4 AC load Voltage (V)

When receiving Meter Get Command, it will report Meter Report Command to the

node.

 

Meter Get Command:

 [Command Class Meter, Meter Get, Scale =0x04(V)]

Meter Report Command:

[Command Class Meter

Meter Report

Rate Type = 0x01

Meter Type =

0x01

Precision = 1

Scale = 0x04

Size = 2

, 

Meter Value(V)]

Example:

Scale = 0x04 (V)

Precision = 1 

Size = 2 (2 Bytes of  V)

Meter Value 1 =  0x09(V)

Meter Value 2 =  0x01(V)

AC load Voltage =  (Meter Value 1*256) +(Meter Value 2)= 230.5 (V)

2-2-5 AC load current ( I )

When receiving Meter Get Command, it will report Meter Report Command to the

node.

Meter Get Command:

 [Command Class Meter, Meter Get, Scale =0x05(I)]

Meter Report Command:

[Command Class Meter

Meter Report

Rate Type = 0x01

Meter Type = 

0x01

Precision = 2

Scale = 0x05

Size = 2

Meter Value(

I

)]

Example:

Scale = 0x05 (

I

)

Precision = 2 

Size = 2 (2 Bytes of 

I

)

Meter Value 1 =  0x01(

I

)

Meter Value 2 =  0x21(

I

)

AC load current =  (Meter Value 1*256) +(Meter Value 2)= 2.89 (A)

2-2-6 load power factor (PF)

When receiving Meter Get Command, it will report Meter Report Command to the

node.

Meter Get Command:

 [Command Class Meter, Meter Get, Scale =0x06(PF)]

Meter Report Command:

[Command Class Meter

Meter Report

Rate Type = 0x01

Meter Type =

0x01

, 

Precision = 2

Scale = 0x06

Size = 1 Bytes

Meter Value(PF)]

Example:

Scale = 0x06 (PF)

Precision = 2

Size = 1 (1 Byte of  PF)

Meter Value 1 =  0x63(PF)

Load power factor (PF) = Meter Value 1 =0.99

8

Summary of Contents for PAN10













Reviews: