Philio Technology Corporation PSR07 Manual Download Page 5

Button no 
response

1. The button will no 

response when LED
is flashing.

Wait for the LED go out and
try again. 

Specification

Operating Voltage

3.7 V (Lithium Polymer Battery)

Low Battery Voltage

3.6 V

Battery Charge Voltage 5 Vdc @ Micro USB Port

RF Range

Minimum 40 m in door, 100m outdoor  line 
of sight

Operating Temperature -10°C ~ 45°C

Frequency Range

PSR07 (EU): 868.40MHz; 869.85MHz(EU)

PSR07 (US): 908.40MHz; 
916.00MHz(USA/Canada) /

PSR07 (TW/JP): 922.5MHz/ 923.9MHz/ 
926.3MHz (Taiwan/JP)

RF Maximum Power

+5dBm

** Specifications are subject to change and improvement without
notice.              

 

         

   

Disposal

 

This marking indicates that this product should not be
disposed with other household wastes throughout the 
EU. To prevent possible harm to the environment or 
human health from uncontrolled waste disposal, 
recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device, 
please use the return and collection systems or 
contact the retailer where the product was purchased.
They can take this product for environmental safe 
recycling.

Company of License Holder

Philio Technology Corporation

Address of License Holder

8F.,No.653-2,Zhongzheng Rd., 

Xinzhuang Dist., New Taipei City 24257,Taiwan(R.O.C)

FCC Interference Statement

This equipment has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to Part 15 of the FCC 
Rules. 
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the in-
structions, may cause harmful interference to
radio communications. 
However, there is no guarantee that interference will not occur in
a particular installation. 
If this equipment does cause harmful interference to radio or tele-
vision reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the fol-
lowing measures:
• Reorient or relocate the receiving antenna.

5

Summary of Contents for PSR07







Reviews: