manualshive.com logo in svg

PHICOMM FD-221, User Manual

The PHICOMM FD-221 is a premium-quality smart home surveillance camera designed to provide advanced security solutions. Enhance your home's safety with this sleek and feature-packed device. For complete control and understanding, don't forget to download the free user manual from our website manualshive.com for easy installation and setup.

Share
Download
background image

                                                        

 

 

 

ADSL2/2+ Modem Router 

www.phicomm.com

 

6

 

Chapter 3: Quick Installation 

 

Chapter 3: Quick Installation   

Configure Your PC 

After you directly connect your PC to FD-221 or to a Hub/Switch which has connected to this 
Modem Router,

 

we suggest you set your computer to obtain the IP address automatically.

 

1)

 

Click Start > Control Panel. 

For Windows XP/2000 

 

 

 

Summary of Contents for FD-221






























































Reviews:

No comments

Related manuals for FD-221

red lion Yaskawa 2000 Information Sheet preview
Yaskawa 2000
Brand: red lion Pages: 5
TP-Link Archer VR500vd Installation Manual preview
Archer VR500vd
Brand: TP-Link Pages: 7
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Brand: Paradyne Pages: 10
Magma ExpressBox2 EB2 User Manual preview
ExpressBox2 EB2
Brand: Magma Pages: 74
H3C MSR 930 Installation, Quick Start preview
MSR 930
Brand: H3C Pages: 4
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Brand: Xantech Pages: 16
JLCooper Electronics GangWay32 User Manual preview
GangWay32
Brand: JLCooper Electronics Pages: 12
EMC VNX5300 Block Hardware Information Manual preview
VNX5300 Block
Brand: EMC Pages: 88
ZyXEL Communications Prestige 643 User Manual preview
Prestige 643
Brand: ZyXEL Communications Pages: 191
Proxim Lynx.GX 16T Installation And Management Manual preview
Lynx.GX 16T
Brand: Proxim Pages: 45
Proxim 68568r1 Installation And Management Manual preview
68568r1
Brand: Proxim Pages: 65
IBA ibaBM-FOX-i-3o-D Manual preview
ibaBM-FOX-i-3o-D
Brand: IBA Pages: 13
Buffalo TERASTATION HS-D1.0TGL/R5 Technical Specifications preview
TERASTATION HS-D1.0TGL/R5
Brand: Buffalo Pages: 2
Gigamon GigaVUE H Series Hardware Installation Manual preview
GigaVUE H Series
Brand: Gigamon Pages: 55
Quamtum HotSpot HS2 User Manual preview
HotSpot HS2
Brand: Quamtum Pages: 42
H3C RA5100 Manual preview
RA5100
Brand: H3C Pages: 11
Fujitsu PCNA EP OCe14102 Installation Manual preview
PCNA EP OCe14102
Brand: Fujitsu Pages: 20
Fujitsu PR-LN4 Software Manual preview
PR-LN4
Brand: Fujitsu Pages: 34

Brands by name

Popular brands

Load more brands