Pfaff Creative 7550 Service Manual Download Page 87

Page: 87 / 116

F'rtting:

•

Insert the new feed stepping motor complete with bracket (fi

37b).

•

Insert and lightly tighten upper retaining screw 16.

•

Insert and lightly tighten clamp spring 15a with screw 16.

•

Push slide block 12 with spring onto the

bolt

and set it in the guide slot in the

correct

curve radius

Check that the slide block moves freely, but without play or binding, in the guide slol

•

Push guide lever 15 complete with the stepping motor carefully to the left, until there Is a clearance

of 0.05 mm between the slide block and the connecting bar.

•

Tighten screws 16 and check that the slide block moves freely, but without

play

•

Push link 1 0 complete wi

t h cam lever 9 to the right onto the connecting bar pin.

•

Fold cam lever 9 to the rear and then over feeding eccentric 20

•

Insert screw 18 In fulcrum stud 19 and tighten it a little.

•

Shift fulcrum stud 19 laterally so that link 1 0 and the connecting bar still have a slight play and

can move freely.

•

Tighten screw 18.

Connect spring 14.

•

Insert cable guide 180 and secure it with screw 181 {hg.

7a)

•

Install transverse-drive stepping motor according to section 38.

•

Push synchronizer 34 onto the shaft making sure that the housing rib is between the two guide

amp

•

Place five-wire flat cable 127 in cable guide 119.

•

Place seven-wire ftat cable 200 in the cable guide.

•

Insert the complete buttonhole sensor.

•

Secure the free-arm cover with two screws.

•

Place the five-wire and the four-wire flat cables in the cable guides.

• Set

the complete baseplate against the machine.

Summary of Contents for Creative 7550





















































































































Search results

Summary of Contents for Creative 7550

Reviews:

Pfaff Creative 7550, Service Manual, Page: 87 / 116

Search results

Summary of Contents for Creative 7550

Reviews: