Pfaff Creative 7550 Service Manual Download Page 75

Page: 75 / 116

35.

Changing the

cable

reel

n the

toot control

Note:

In Germany the

fool

control must be exchanged along

with the

cable reel.

Remov•l

of the cable

reel:

•

lift

rubber strip 167

and

pull

it out with

its three feet (fig. 35).

•

Pull out the

two

plugs 165.

•

Unscrew the lour Philips screws 168

•

Remove housing cover 166.

•

Remove the rectangular pedal 169 with guide 170 and take out contact spring 179.

•

Disconnect the right pressure spring 17.8.

•

Disconnect the right cable 177 with the contact eyelet (fig.

35a).

•

Press out or pull out cemented resistor track 172 (20-KO-potentiometer) upwards with a

screwdriver

a pair

pliers.

•

Remove cable reel 176.

Flttlng:

•

out the

cable by approximately 10

and insert cable reel 176 into the housing.

•

Insert

the

soldered resistor track 172 fully downwards into

the

guide and secure

it with

some

adhesive.

Push

the

soldered contact eyelet 177 onto

the

right guide pin.

•

Place both cables in the respective guide grooves.

Place contact spring 179 on the guide pin In the larger right section of pedal 169.

Push pressure spring 178 onto the same guide pin.

Turn pedal 169 around and push the right spring 178 on the right guide pin of the housing and the

left spring 171 on the

left

guide pin In pedal 169.

• Arst

press the pedal a little to the right and then downwards in such a way that contact spring 179

Is on the right-hand

side

of resistor tracl< 172 and Is not bent

Press the pedal further down,

far

as lt will

go: at the same time insert guide 170 In

its two

open

bearings.

Hold

pedal

169 in this position; at

the

same time replace housing cover 166 and press

firmly

the

housing (fiQ. 35).

•

Insert and tighten

the

four Phillps

screws.

•

Insert rubber strip 167 and

the two

plugs 165.

• Carry out

a performance

test

e Use

testing appliance

ABB

Metrawatt M 5013

carry out an

electrical

safety test according to

VDE 0701.

Summary of Contents for Creative 7550





















































































































Search results

Summary of Contents for Creative 7550

Reviews:

Pfaff Creative 7550, Service Manual, Page: 75 / 116

Search results

Summary of Contents for Creative 7550

Reviews: