manualshive.com logo in svg

Petsafe Elite Pendant PDT00-13377, Operating And Training Manual, Page: 6 / 28

Share
Download
Petsafe Elite Pendant PDT00-13377 Operating And Training Manual Download Page 6

6 

Customer Care Center 1-800-732-2677

Operating Guide

Step 1

Prepare the Handheld Remote

Charge the Handheld Remote

1. Lift the rubber cover protecting the Remote’s Micro USB Port 

and insert one of the Micro USB connectors (

1A).

2. Insert the USB connector on the opposite end into the power 

adapter (

1B) and plug into a standard wall outlet.

3. Charge the Handheld Remote for 5 hours for the first charge. 

Recharges take only 3-4 hours. Note: The Status Gauge will 

have a solid red LED while charging and a solid green LED 

when fully charged.

4. When charging is completed, replace the rubber cover.
Note: Approximate battery life between charges is 40 to 50 

hours, depending on frequency of use. Ensure the Handheld 

Remote is closed when no longer in use for longer battery life.
Note: Both the Handheld Remote and the Pendant

™

 can also be charged by plugging into a USB port 

on your computer. Charging time may be longer than when using the power adapter.

Turning On the Handheld Remote

Power up the Handheld Remote by sliding it open. You will see the status gauge display the 

remaining battery life.

Handheld Remote LED - Function and Response

Handheld Remote Function

Status Gauge LED Response

Good battery

3 green LEDs are solid for 3 seconds

Medium battery

2 green LEDs are solid for 3 seconds

Low battery

1 green LED is solid for 3 seconds

Critical battery

Red LED flashes for 3 seconds

Any stimulation button pressed

Red LED is solid for length of button press

Tone button pressed

1 green LED is solid for length of button press

Step 2

Prepare the Pendant

™

 Receiver 

Charge the Pendant

™

 Receiver

1. Lift the rubber cover protecting the Pendant’s Micro USB Port and insert one of the Micro 

USB connectors (

2A).

2. Insert the USB connector on the opposite end into the power adapter (

1B) and plug into a 

standard wall outlet. The red light will appear. Note: The Handheld Remote and the Pendant

™

 

Receiver can both be plugged in to the charger at the same time.

USB Cable 

placed in the 

Handheld 

Remote Micro 

USB Port

1A

1B

Summary of Contents for Elite Pendant PDT00-13377





























Reviews:

No comments