Pertronic SYSTEM SENSOR FAAST LT Series Installation And Maintenance Manual Download Page 16

Page: 16 / 22

FAAST LT Loop-Based Installation & Maintenance Guide Iss 1.0, 201701

Section D : MONITORING FAAST LT using PipeIQ

This section identifies options for testing the FAAST LT and monitoring its environment:

Actions:

The PipeIQ™

Actions

tab enables:



Test Relays



Smoke Test



Test Fan speed



Alarms Test



Sounder



Restart



FAAST LT Clock



Operating Hours



Reset

D1a Test Relays:

to test relays

a. Click

Monitoring

on the left pane.

b. Select the device to set the actions. The

Actions

tab appears on the right pane.

c. Under

Test Relays

, set the following relays.

i. Alarm Relays:



Under

Alarm 1

and

Alarm 2

, click the status button to activate or deactivate the alarm.

ii. Pre-Alarm Relays



Under

Pre-Alarm 1

and

Pre-Alarm 2

, click the status button to activate or deactivate the Pre-Alarm.

iii. Sounder Relays



Under

Sounder 1

and

Sounder 2

, click the status button to activate or deactivate the sounder relay.

iv. Fault Relays



Under

Fault

and

Aux Fault

, click the status button to activate or deactivate the fault relay

Note:

Click

Refresh

to obtain the current state of all the relays

D1b Smoke Test:

to perform Smoke Tests

a. Click

Monitoring

on the left pane.

b. Select the device to set the actions. The

Actions

tab appears on the right pane.

c. Under

Smoke Test

, set the time for the following two options:

i. Start at a set time:



Select

Start at

and select the time to schedule a start time for the smoke test



Click

Schedule

ii. Start now



Select

Now



Click

Start



The

Alarm Time

(mins/secs) specifies the measured time between the insertion of smoke and

activation of an Alarm



The

Transport Time

(mins/secs)

specifies the measured time between the insertion of smoke into

the pipe system and the time taken for the smoke particles to reach the detector.
The measurement is stopped when the smoke level reaches

Level 1



Click

Stop

D1c Test Fan Speed:

to test Fan Speeds

a. Click

Monitoring

on the left pane.

b. Select the device to set the actions. The

Actions

tab appears on the right pane.

c. Under

Test Fans Speed

, set the channel speed:

i. Set the

Channel 1

speed on the scale

ii. Click

Test Fan 1

The Fan 1 speed rate is checked and the change in

Flowrate 1

is displayed

iii. Click Stop

Note:

Repeat Steps i. through iii. to set the speed for

Channel 2

Summary of Contents for SYSTEM SENSOR FAAST LT Series























Search results

Summary of Contents for SYSTEM SENSOR FAAST LT Series

Reviews:

Related manuals for SYSTEM SENSOR FAAST LT Series

Brands by name

Popular brands

Pertronic SYSTEM SENSOR FAAST LT Series, Installation And Maintenance Manual

Search results

Summary of Contents for SYSTEM SENSOR FAAST LT Series

Reviews:

Related manuals for SYSTEM SENSOR FAAST LT Series

Brands by name

Popular brands