manualshive.com logo in svg

Permobil Halsa, Owner'S Manual

Share
Download
Permobil Halsa Owner'S Manual Download Page 2

Hälsa Bed Owner’s Manual 

 

Version 2.0 August 2018 © Permobil 2018 

This document may not be reproduced, copied or used for purposes  

other than its intended use without the prior written consent of Permobil. 

This manual includes installation instructions as well as important safety and 

maintenance information for your Hälsa Bed. 

All information, pictures, illustrations and specifications are based upon the product 

information available at the time this manual was created. 

The information in this document is subject to change without notice. 

ALL RIGHTS RESERVED 

 

 

Technical and Customer Support 

In the event of any issues, contact your dealer or call  

Permobil Canada at 800-265-9830. 

Be prepared to provide the bed serial number. 

Spare parts and accessories may be ordered through your dealer. 

 

Permobil Canada 

2215/2221 46e Avenue 

•

 Lachine, QC   H8T 3C9 

Tel: 800-265-9830 

•

 Fax: 877-636-8944 

•

 Email: [email protected] 

www.permobil.ca 

 

Summary of Contents for Halsa









































Reviews:

No comments

Brands by name

Popular brands

Load more brands