background image

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice 

10

Form No. Z2325

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

18” SHALLOW-DEPTH SERIES

Operation/Installation Manual

C

O

O

LE

R

OFF

1

2

3

4

5

6

COLD

Figure 7. Control Panel

OPERATION

General

The  unit  is  equipped  with  a  state-of-the-art 

refrigeration system and is a frost-free model. The 

evaporator coil automatically defrosts on demand 

during off cycle.

Interior Light

The  unit  is  equipped  with  an  interior  light  that 

illuminates  when  the  door  is  opened.  A  manual 

switch  is  located  next  to  light  for  displaying  the 

product  through  a  glass  door.  Always  ensure 

the  manual  switch  is  in  the  off  position  before 

closing a solid door. If manual switch is left on for 

an  extended  period  of  time,  it  may  increase  the 

cabinet  temperature,  especially  at  the  top,  and 

cause the refrigeration system to run longer.

Loading Product
IMPORTANT:

   

When  loading  items  into  unit,  do 

not block interal louvers and fan guard openings 

or performance will be decreased.

Temperature Control

The controller is located at the top rear panel of 

the  cabinet  (

Figure  7

).  Approximate  temperature 

operating ranges are:

 

 Refrigerator:   33°F minimum, 39°F maximum 

 

 Wine Reserve:   40°F minimom, 65°F maximum 

 

Adjusting the Temperature

 

 Colder Temperature: Turn the adjusting screw 

clockwise (to the right) 

 

 Warmer Temperatures: Turn the adjusting scrw 

counterclockwise (to the left) 

 

 Temperature Control “OFF”: Turn the adjusting 

screw completely counterclockwise to the 

“OFF” position until a click is heard. 

The condenser fan and motor turns off and on with 

the compressor.

Summary of Contents for HD24 SERIES

















Reviews: