background image

Connecting the Regulator to the
CO

2

 Cylinder 

 

  ■ 

Remove blue plug from regulator fitting. 

 

(Note: Do not remove the carbonic washer).

  ■ 

Screw regulator onto gas cylinder valve.  

 

Tighten with wrench until vertically straight.  

 

Be sure that shut-off valve (

black lever

) on  

 

regulator is in the OFF (

horizontal

) position.

  ■ 

Place a screw clamp over end of red air line  

 

and push onto regulator tailpiece. Tighten  

 

clamp with a screwdriver.

Adjusting the CO

2

 Gas flow 

  ■ 

Turn regulator adjusting screw counterclock- 

 

wise until it turns freely.

  ■ 

Turn hand valve counterclockwise on CO

2

 

 

cylinder to the fully open position.

  ■ 

Turn regulator adjusting screw clockwise until  

 

desired pressure is reached (approximately  

 

12-15 lbs.). The desired pressure may vary  

 

based on location/elevation. Tighten stop nut  

 

on adjusting screw.

  ■ 

Open shut-off valve on bottom of regulator.

 

CO

Leak Test 

Dilute a small amount of liquid dish washing soap 

and rub the soapy mixture around each connec-

tion. If bubbles appear, tighten connection.

 

Replacing CO

Gas Cylinder 

  

  ■ 

Turn CO

2

 hand valve clockwise until seated and  

 

close shut-off valve on regulator.

  ■ 

unscrew regulator from cylinder fitting.

  ■ 

Replace carbonic washer (Part No. 157F2P), 

 

if needed and reattach regulator to filled  

 

cylinder.

  ■ 

Turn CO

2

 hand valve counterclockwise until 

 

fully open. Turn regulator shut-off valve to 

 

open position.

  ■ 

Adjust CO

2

 gas flow as required, turning

 

clock wise for higher pressure.

Proper CO

Handling 

  

always

...

  ■ 

Connect a regulator (reducing valve) to  

 

CO

2

 cylinder.

  ■ 

Secure cylinder in upright position whether in  

 

storage or in use.

  ■ 

Keep cylinder away from heat. Rupture disc  

 

vents at 122° F. maximum.

  ■ 

Ventilate room after high pressure gas leakage.

  ■ 

Check the last DOT test date on cylinder neck  

 

before filling. If more than five years old, the  

 

cylinder must be retested to DOT specifications.

  ■ 

Be sure CO

2

 cylinder outlet fitting is free of dust  

 

or dirt before attaching regulator.

  ■ 

Store CO

2

 cylinder and regulator assembly  

 

upright.

  ■ 

Allow only properly trained and experienced  

 

personnel to handle high pressure gas. 

 

never

...

  ■ 

Connect cylinder directly to a keg without a 

 

regulator (reducing valve).

  ■ 

Drop or throw regulator or CO

2

 cylinder.

  ■ 

Transport CO

2

 cylinder in a closed vehicle.

  ■ 

Apply oil to a regulator. 

 

  ■ 

Shut off CO

2

 cylinder when not in use. You will  

 

not save gas by doing so!

  ■ 

Allow untrained, inexperienced personnel to  

 

handle high pressure gas.

failure to heed this warning could result in  

personal injury or death.

Form No. Z2323

Rev. 06.26.10

5

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.

Installation and Tapping

ArctiCold Draft Dispenser

CO2

PRESSURE

GAUGE

CO2 

GAS 

DRUM

REGULATOR

FITTING

REGULATOR

ADJUSTING

SCREW

FITTING FOR

RED AIR HOSE

SHUT-OFF VALVE

(BLACK LEVER IN

CLOSED POSITION)

HAND

VALVE

PERLICK

PSI

10

50

0

60

20

40

30

Summary of Contents for DC90ACLT













Reviews: