Perlick BBRN Series Installation & Operation Manual Download Page 20

 

Models BBRN/BBSN Installation & Operation Manual

Printed in USA 

20 0213

WARRANTY

The terms and conditions set forth below 

together with those appearing on the face of 

the Acknowledgement (the “Order”) constitute 

the complete and exclusive agreement between 

Perlick Corporation and the Buyer pertaining to 

the  goods and/or services identified in the Order. 

If there is a  discrepancy or conflict between any 

exhibit  or  supplement  to  the  Order  and  these 

terms and conditions, these terms and conditions 

shall control. The Order is intended by Seller and 

Buyer  to  be  the  complete,  exclusive,  and  final 

statement of their agreement. Any changes to an 

Order must be in writing and signed by Perlick 

and Buyer.

TERMS NET 30 DAYS

Payment by Visa, MasterCard, American Express 

or Discover card accepted or cash in advance 

unless prior accommodations have been made 

with our Credit Department. Please direct inquiries 

for detailed information to our Credit Manager. 

All  sales,  excise,  or  similar  taxes  required  by 

law to be collected or paid by  seller shall be in 

addition to prices quoted unless an  appropriate 

Tax Exemption certificate is furnished. All goods 

are  sold  F.O.B.  factory.  Except  for  otherwise 

provided, Perlick will not be responsible for freight, 

transportation, insurance,  shipping, storage, 

handling, demurrage or similar charges.  Invoices 

are payable in full in thirty (30) days following 

the invoice‚s date of issuance. If by the terms 

of sale credit is extended, Perlick reserves the 

right to revoke such credit if buyer fails to pay 

for any products when due and may demand 

payment prior to the commencement of any 

further shipment.

WAIVER

Any waiver of strict compliance with the provisions 

of an Order must be in writing. No such waiver 

shall be construed as a waiver of any other term 

or condition except as provided in writing, nor as 

a waiver of any subsequent breach of the same 

term or condition.

METHOD OF SHIPMENT

All shipments are carefully packed and labeled. 

Crates, boxes and cartons used are of approved 

weight and strength.  Freight rates are based upon 

100 pound minimum.

LOST and DAMAGED MERCHANDISE

THE  RESPONSIBILITY OF THE PERLICK 

CORPORATION CEASES UPON ACCEPTANCE 

OF ITS PRODUCTS BY THE CARRIER. Any 

damage or loss sustained in shipment is the 

carrier’s responsibility. Before giving the carrier 

a clean receipt at time of delivery, make sure you 

receive every item on the bill and inspect every 

carton,  crate  and  box  for  concealed  damage, 

i.e., broken boards, crushed or punctured 

cartons, torn cardboard. IF ANY ITEMS ARE 

SHORT OR DAMAGED, DO NOT ACCEPT THE 

SHIPMENT UNLESS THE CARRIER MAKES A 

NOTATION OF THIS ON YOUR FREIGHT BILL. 

Then request an inspection. Do not destroy the 

packing materials. If their agent does not make 

an inspection within five days, advise the carrier 

via  letter  that  you  notified  them  regarding  the 

matter and they have failed to act. You will need 

this letter to support your claim. Then file a claim 

for your loss. When you give the carrier a clean 

receipt, you accept the total responsibility for the 

shipment. UPS shipments are insured individually 

and UPS will replace all merchandise that is lost 

or damaged.

RETURN OF MERCHANDISE

Do not return any merchandise without our 

approval. Merchandise returned without a return 

merchandise  authorization number will not be 

accepted at Perlick. Used, discontinued, and 

certain custom made items cannot be returned for 

credit. These custom items include non-catalog 

products (specials) as well as custom assembled 

catalog products. Catalog items are designated 

as non-returnable on the price list page on which 

they appear. Items returned must be in new 

condition and packaged in their original carton 

or crate. Freight charges must be prepaid on all 

return shipments.
When a return is authorized, a credit may be 

allowed pending an examination of the returned 

goods. The amount of the restocking charge will 

depend on the condition of  the equipment. The 

minimum restocking charge for glass washers, 

bottle coolers, frosters, direct draws, cooler 

series back bars and accessory parts is 20%. 

The minimum restocking charge for custom 

series cabinets is 50%. The  minimum restocking 

Summary of Contents for BBRN Series

























Reviews: