manualshive.com logo in svg

Perkins 402F-05, Operation And Maintenance Manual, Page: 74 / 88

Share
Download
Perkins 402F-05 Operation And Maintenance Manual Download Page 74

i04145953

Fuel System - Prime

 

Turn the keyswitch to the ON position for 2 minutes in
order to prime the fuel system. Turn keyswitch to OFF
position, then turn on again. The engine is primed
and ready to start.

i05337705

Fuel System Primary Filter -
Replace

 

Fuel leaked or spilled onto hot surfaces or electri-
cal components can cause a fire. To help prevent
possible injury, turn the start switch off when
changing fuel filters or water separator elements.
Clean up fuel spills immediately.

NOTICE

Ensure that the engine is stopped before any servic-
ing or repair is performed.

Remove the Element

1.

Turn the fuel supply valve (if equipped) to the OFF

position before performing this maintenance.

2.

Place a suitable container under the water

separator in order to catch any fuel that might spill.
Clean up any spilled fuel. Clean the outside body
of the filter assembly.

Illustration 45

g03381282

Typical example

3.

Remove the filter bowl (4) from the fuel filter base

(1).

4.

Remove the O-ring seal (3). Discard the O-ring

seal.

5.

Remove the filter element (2) from the fuel filter

base (1). Discard the filter element (2).

6.

Clean the filter bowl (4).

Install the Element

74

SEBU9064

Maintenance Recommendations
Fuel System - Prime

Summary of Contents for 402F-05

























































































Reviews:

No comments