Perkins 402F-05 Operation And Maintenance Manual Download Page 28

Page: 28 / 88

(Table 7, contd)

Actuator drive malfunction.
Disconnection of Speed sensor
connector.
Disconnection of Speed sensor
harness.

The engine will shut down.

Check harness connection. If the
fault remains contact your Perkins
dealer or your Perkins distributor.

Speed sensor malfunction.
Disconnection of Speed sensor
connector.
Disconnection of Speed sensor
harness.

The engine will go into limp home
mode.

Check harness connection. If the
fault remains contact your Perkins
dealer or your Perkins distributor.

(1)

Checking engine oil is part of the daily engine check. Operating an engine will a low level of engine oil can damage your engine.

For more information on diagnostic messages and
diagnostic tools contact your Perkins dealer or your
Perkins distributor.

SEBU9064

Engine Diagnostics
Diagnostic Flash Code Retrieval

Summary of Contents for 402F-05
























































































Search results

Summary of Contents for 402F-05

Reviews:

Perkins 402F-05, Operation And Maintenance Manual, Page: 28 / 88

Search results

Summary of Contents for 402F-05

Reviews: