Pergola kits USA CLASSIC CEDAR PERGOLA KIT Assembly Manual Download Page 9

7

Anchor remaining Posts to Concrete

15.) Sliding the base up towards the top you 
can fasten it to the post with a screw to keep 
it from falling down. Make sure the posts are 
level and still at the L-shaped pencil mark. 
Screw the second bracket to the post using 
(5) 2 ½” screws. It does not matter which side 
of the post, however we recommend going 
caddy-corner. Keep in mind you should stay 
approximately 4” away from the edge of the 
concrete. Refer back to step 6 for setting the 
brackets. Once completed remove the screw 
and place the base in its correct position. 

Installing Rafters

16.) A helper may be needed to hold the posts 
in place when positioning the first rafter. Make 
sure that the overhang is the same on both 
ends of the rafter. Measure from the beam
to the end of the rafter, or to the beginning of 
the scroll cut on both sides (as shown above). 
Slide the rafter until the overhang is the
same on both ends. 

P a g e

 | 

21.

 

Now you would be ready to install the 
return beams. These go in between the 
header. Keep it flush on bottom of 2x8 
header center of post. Attach it with 4 
3½" screws.

Section 6 - Setting Runners

22.

 

Use a level to insure that the posts are 
parallel with the other posts. Check 
that one of the posts is plumb. 
Measure the distance between the 
posts at the bottom, by sliding the 
post base up and measuring the 
distance at the bottom of the post. Be 
sure that the posts are the same 
distance apart near the top. Double 
check all posts with the level before 
attaching runners.

 

23.

 

A helper may be needed to hold 
the posts in place when positioning 
the first runner. Make sure that the 
overhang is the same on both ends of 
the runner. Measure from the beam 
to the end of the runner, or to the 
beginning of the scroll cut on both 
sides. (as shown to the right) Slide the 
runner until the overhang is the 
same on both ends. 

24.

 

Attach one side using a screw on an 
angle as shown. Attach each runner 
to both beams on each side.

Using 3½" screws

4 per runner

Summary of Contents for CLASSIC CEDAR PERGOLA KIT













Reviews: