Performax 240-3600, Operator'S Manual, Page: 12 / 40

Page 11
CONTENTS
Blade guard . . . . . . . . . . . . . . . . . . . . 1 pc
Anti-kickback pawls . . . . . . . . . . . . . . 1 pc
Miter gauge . . . . . . . . . . . . . . . . . . . . . 1 pc
Rip fence . . . . . . . . . . . . . . . . . . . . . . . 1 pc
Handle assembly . . . . . . . . . . . . . . . . 1 pc
Push stick . . . . . . . . . . . . . . . . . . . . . . 1 pc
Blade wrench . . . . . . . . . . . . . . . . . . 2 pcs
Hex key 5/32” (4mm) . . . . . . . . . . . . . 1 pc
Hex key 15/64” (6mm) . . . . . . . . . . . . 1 pc
Dado throat insert . . . . . . . . . . . . . . . . 1 pc
Limit-support . . . . . . . . . . . . . . . . . . . 1 pc
Assistant-support . . . . . . . . . . . . . . . . 1 pc
Leg . . . . . . . . . . . . . . . . . . . . . . . . . . 4 pcs
Long carriage bolt . . . . . . . . . . . . . . 6 pcs
Short carriage bolt . . . . . . . . . . . . . . 4 pcs
Washers . . . . . . . . . . . . . . . . . . . . . 20 pcs
Lock-nuts . . . . . . . . . . . . . . . . . . . . 2 pcs
Nuts . . . . . . . . . . . . . . . . . . . . . . . . . 8 pcs
UNPACKING
This product requires assembly .
1 . Carefully lift the saw from the carton
and place it on a level work surface .
2 . Inspect the tool carefully to make sure
that no breakage or damage occurred
during shipping .
3 . Do not discard the packing material
until you have carefully inspected and
satisfactorily operated the tool .
4 . The saw is factory set for accurate
cutting . After assembling it, check for
accuracy . If shipping has influenced the
settings, refer to specific procedures
explained in this Operator’s Manual .
5 . If any parts are damaged or missing,
please call 1-866-858-2664 for
assistance .
If any parts are damaged or missing, do not
operate this tool until the parts are replaced .
If any parts are
damaged or missing, do not operate this
tool until the parts are replaced. Failure
to heed this warning could result in
serious personal injury.
Do not attempt to
modify this tool or create accessories not
recommended for use with this tool. Any
such alteration or modification is misuse,
and could result in a hazardous condition
leading to possible serious personal
injury.
Do not connect to the
power supply until assembly is complete.
Failure to comply could result in
accidental starting and possible serious
personal injury.
Never stand directly in
line with the blade or allow hands to come
within 3” (7.6 cm) of the blade. Do not
reach over or across the blade. Failure to
heed this warning can result in serious
personal injury.
To avoid serious
personal injury, always make sure the
table saw is securely mounted to a
workbench or an approved leg stand.
NEVER operate the saw on the floor.
STAND SET-UP
The saw can be used for cutting operations
using the stand .
INSTALL THE STAND
(FIG. 2a - 2b)
1 . Put the limit-support on a flat surface, and
insert the assistant-support . Align the
holes in the supports .
2 . Place a washer onto each of the long
carriage bolts . Insert the long carriage
bolts up through the holes in the
supports . Place a washer and a
lock-nut on the threads of each bolt .
Tighten all lock-nuts securely .
3 . Insert the legs into the supports; align
the holes in the legs with the holes
in supports .
ASSEMbLy
WARNING:
WARNING:
WARNING:
WARNING:
WARNING: