3
3111435 | ED. 01 | 01 - 2021
ULTRANIK
HF motion detector
B
For staircase and corridor (master and slave)
SECTION 2 : REMOTE CONTROL
While the 1st sensor detects motion on the 1st floor, it switches the light on at 100% and sends signal to all
slave units. All slaves on the 1st floor turn on and the sensor highbay on the 2nd floor switches on at
stand-by level.
The person walks to the 2nd floor, the 2nd Sensor highbay switches the light on at 100%. All slaves on the
2nd floor turn the light on and the Sensor highbay on the 3rd floor switches on at stand-by level.
10%
OFF
OFF
100%
100%
100%
OFF
OFF
OFF
OFF
OFF
OFF
MASTER
SLAVE
CORRIDOR
100%
100%
100%
100%
100%
10%
OFF
OFF
OFF
OFF
OFF
CORRIDOR
MASTER
SLAVE
The person walks to the 3rd floor, the 3rd sensor highbay switches the light on 100%. All slaves on the 3rd
floor turn the light on and the Sensor highbay on the 4th floor switches onat stand-by level. Meanwhile,
the lights on the 1st floor are dimmed to stand-by level after hold-time.
The person walks to the 4th floor, the 4th sensor highbay switches the light on at 100%. All slaves on the
4th floor turn the light on Meanwhile, all sensors on the 1st floor turn the light off after stand-by period,
and all lights on the 2nd floor dim to stand-by level after hold-time.
PERMANENT ON/OFF
( button
1
)
Press button
1
, to select permanent ON or permanent OFF mode.
* Press button
2
/
4
to resume automatic operation.
The mode will change to AUTO Mode after power failure.
RESET
( button
2
)
Press button
2
, all settings go back to the default settings :
Detection range: 100% Hold time: 1min Stand-by period: 5min Stand-by dimming level: 20% Daylight sensor: LUX disable
SHIFT
( button
3
)
Press button
3
, the LED on the top left corner will flash to indicate mode selection. All values / settings in RED are valid for 20 seconds.
AUTO MODE
( button
4
)
Press button
4
, to initiate automatic mode. The sensor starts working and all settings remain as before the light was switched ON/OFF.
SEMI-AUTO MODE
( button
3
&
4
)
1. Press button
3
Shift (the red LED is on for indication)
2. Press button
4
to initiate semi-auto mode. The fixture is manually on by push-switch and automatically off in semi-auto mode.
POWER OUTPUT
( button
5
)
Press button
5
, the light output shifts between 80% and 100%.
Note: the function of “Sensor off” and “Twilight” are disabled.
BRIG/-
( button
6
)
Press button
6
to adjust the light brightness between 10%~100% .
SCENE PROGRAM
( zone
7
) (One-key-commissioning)
1. Press button “start” to program.
2. Select the buttons in
8
“Detection range”,
9
/
10
“Daylight hreshold”,
11
“Hold time”,
12
“Stand-by time”,
13
“Stand-by dimming
level” to set all parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s). For example, to pre-set detection range 100%, daylight threshold Disable,
hold time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be as follows: Press button
7
Start, button
8
100%,
10
Disable,
3
Shift,
11
5min,
3
Shift,
12
+∞,
13
30%,
7
Memory. By pointing to the sensor unit(s) and pressing
7
Apply, all
settings are passed on the sensor(s).
1
3
100%
100%
10%
10%
10%
100%
100%
100%
10%
OFF
OFF
CORRIDOR
MASTER
SLAVE
10%
10%
10%
OFF
OFF
OFF
100%
100%
100%
100%
100%
CORRIDOR
MASTER
SLAVE
HRC-11
Note: the red LED indicator flash one time when RC
receives signal successfully
7
3
1
6
5
2
4
4
2