background image

2

Capacity:...............................................................................  100,000 lbs.

Minimum Lift Height: ..................................................................  11-3/4 in.

Maximum Lift Height: ................................................................. 18-7/8 in.

Base Length: ............................................................................... 8-5/8 in.

Base Width: ................................................................................. 6-7/8 in.

SPECIFICATIONS:

Specifications are subject to change without notice.

This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and troubleshooting 

steps described within to ensure your safety and satisfaction. The contents of this instruction manual are based upon the latest 

product information available at the time of publication. The manufacturer reserves the right to make product changes at any time 

without notice. 

SAFETY GUIDELINES / DEFINITIONS

UNPACKING AND INSPECTION

WARNING: Read and understand this entire instruction manual before attempting to assemble, install, operate or maintain 

this product. Failure to comply with the instructions may result in serious personal injury and/or property damage!
The following signal words are used to emphasize safety warnings that must be followed when using this product:

DANGER: Indicates an imminently hazardous situation 

that, if not avoided, WILL result in death or serious injury.

WARNING: Indicates a potentially hazardous situation that, 

if not avoided, COULD result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation that, 

if not avoided, MAY result in minor or moderate injury.

NOTE: Indicates important information, which if not 

followed, MAY cause damage to equipment.

After opening the carton, unpack your new product and related parts and accessories. Please 

inspect it carefully for any damage that may have occurred during transit. Please check it against 

the photograph on carton. If any parts are missing, please call customer service at 1-800-426-1262 

between 6 a.m. and 5 p.m. Pacific time. 

WARNING: DO NOT operate this product if damaged during shipment, handling or misuse.  

Do not operate the product until the parts have been replaced or the fault rectified. Failure to do 

so may result in serious personal injury or property damage. All damaged parts must be repaired 

or replaced as needed prior to operating this product. Check to see that all nuts, bolts and fittings 

are secure before putting this product into service. 

If you have any questions, or require assistance with damaged or missing parts, please contact 

our customer service department at 1-800-426-1262. Please have the serial number, model 

number, and date of purchase available for reference when calling.

IMPORTANT SAFETY INFORMATION

WARNING

READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND WARNINGS BEFORE OPERATING 

THIS TOOL. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY 

DAMAGE AND WILL VOID WARRANTY.

1. Study, understand, and follow all instructions 

before operating this device.

2. DO NOT exceed rated capacity. Overloading 

can cause damage to or failure of the jack.

3. Use only on hard, level surface capable of 

sustaining the load. Use of jack on other than 

hard level surfaces can result in jack instability 

and possible loss of load.

4. Lifting device only. Immediately after lifting, 

support the vehicle with appropriate means. 

Ensure that no personnel pass underneath load 

until load is securely supported by jack stands.

5. DO NOT adjust safety valve.

6. Wear ANSI approved safety goggles and heavy 

duty work gloves during use.

7. Keep clear of load while lifting and lowering.

8. Lower load slowly.

Warning: This is a lifting device only. Load must be supported immediately by Jack Stands.

Summary of Contents for W1637









Reviews: