10
SLEEP FEATURE:
Press SLEEP button to initiate the SLEEP
mode. In this mode, the selected temperature will
increase by 2°F (1°C) 30 minutes after the mode is
selected. The temperature will then increase (cooling)
or decrease (units with heating only) by another
2°F (1°C) after an additional 30 minutes. This new
temperature will be maintained for 6 hours before it
returns to the originally selected temperature. This
ends the SLEEP mode and the unit will continue
to operate as originally programmed. The SLEEP
mode program can be canceled at any time during
operation by pressing the SLEEP button again.
CHECK FILTER FEATURE:
Press CHECK FILTER button to initiate this
feature. This feature is a reminder to clean the Air
Filter for more efficient operation. The LED (light) will
illuminate after 250 hours of operation. To reset after
cleaning the filter, press the CHECK FILTER button
and the light will go off.
ENERGY SAVER FEATURE (ECO):
Press ENERGY SAVER button to initiate this
function. This function is available on COOL, DRY
and AUTO (only AUTO-COOLING and AUTO-FAN)
modes. In this mode, the fan will continue to run for 3
minutes after the compressor shuts off. The fan then
cycles on for 2 minutes, at 10 minute intervals, until
the room temperature is above the set temperature,
at which time the compressor turns back on and
cooling starts.
FOLLOW ME FEATURE:
This feature can ONLY be activated
from the remote control. The
remote control serves as a remote
thermostat, allowing for precise
temperature control at its location.
To activate the Follow Me feature, point the remote
control towards the unit and press the FOLLOW ME
button. The remote displays the actual temperature
at its location. The remote control will send this
signal to the air conditioner every 3 minutes until the
FOLLOW ME button is pressed again. If the unit does
not receive the Follow Me signal during any 7 minute
interval, the unit will beep to indicate use of the
Follow Me feature has ended.
SMART FEATURE:
When using the Smart feature for the first time,
press the SMART button for 3 seconds to initiate
the SMART Discovery mode. The LED Display will
show “AP” for 1 second and then go blank for 2
seconds repeatedly to indicate that it is ready for
you to configure the wireless smart connection. If
the connection is successful within 8 minutes, the
unit will exit Discovery mode automatically and the
SMART indicator will illuminate. The unit can then be
operated in SMART mode. If connection fails within
the first 8 minutes, the unit will exit Discovery mode
automatically and “AP” will disappear. See App Guide
for instructions and additional information.
During the network configuration process, do not try
using the remote control or the controls on the front
panel of the air conditioner as they will be inoperative.
You may use the remote control and front panel
buttons again after the network configuration process
is complete. (The configuration process usually takes
8 – 10 minutes.)
TO SELECT THE OPERATING MODE:
To choose operating mode, press the MODE
button. Each time you press the button, a mode is
selected in a sequence that goes from AUTO, COOL,
DRY and FAN. The indicator light will be illuminated
and remain on once the mode is selected.
The unit
will automatically initiate the Energy Saver function
under COOL, DRY, and AUTO (only AUTO-COOLING and
AUTO-FAN) modes.
TO OPERATE ON AUTO FEATURE:
When you set the air conditioner to AUTO mode, it
will automatically select cooling, or fan only operation
depending on what temperature you have selected
and the room temperature. The air conditioner will
control room temperature automatically around the
temperature you set.
In this mode, the fan speed
cannot be adjusted.
It starts automatically at a speed
according to the room temperature.
TO OPERATE ON FAN ONLY:
Use this function only when cooling is not desired,
such as for room air circulation or to exhaust stale air.
(Remember to open the vent during this function, but
keep it closed during cooling for maximum cooling
efficiency.) You can choose any fan speed you prefer.
During this function, the display will show the actual
room temperature, not the set temperature as in the
cooling mode.
TO OPERATE ON DRY MODE:
In this mode, the air conditioner will reduce air
humidity. If the space is a closed or sealed area,
some degree of cooling will continue.
Light
Flashing
Follow
Me
