background image

To prevent injury to the user or other people and property damage, the following instructions
must be followed. Incorrect operation due to ignoring of instructions may cause harm or 
damage. The seriousness is classified by the following indications.

This symbol indicates the possibility of death or serious injury.

Meanings of symbols used in this manual are as shown below.

!

Always do this.

Never do this.

CAUTION

This symbol indicates the possibility of injury or damage to property.

Plug in power plug properly.

Do not modify power cord 
length or share the outlet with 
other appliances.

Always ensure effective 
grounding.

Always unplug the unit if 
strange sounds, smell or 
smoke comes from the unit.

Do not use firearms near unit.

Ventilate room before operating air conditioner if 
there is a gas leakage from another appliance 
such as a stove.

Failure to do so may cause 
electric shock or fire due to 
excess heat generation

.

Doing so may cause electric 
shock or fire due to heat 
generation.

Incorrect grounding may cause 
electric shock.

Failure to do so may cause fire 
and electric shock.

Doing so may cause fire.

Failure to do so may cause explosion, 
fire and burns.

Doing so may cause electric 
shock or fire due to heat generation. 

Doing so may cause electric shock.

Doing so may cause failure of
machine or electric shock.

Doing so may cause fire and 
electric shock.

Doing so may cause fire and 
electric shock.

Doing so may cause electric shock
or fire. If the power cord is 
damaged, it must be replaced by the
manufacturer or an authorized 
service center or a similarly qualified 
person in order to avoid a hazard.

This could cause health issues.

Incorrect installation may cause fire 
and electric shock.

Doing so may cause electric shock.

Doing so may cause an explosion or fire.

Doing so may cause failure and 
electric shock.

Do not operate or stop the unit

by inserting or pulling out the 

power plug directly from the wall.

Do not operate with wet hands 
or in damp environment.

Do not allow water to run into 
electric parts.

Do not use the socket if it is 
loose or damaged.

Do not use the power cord close
to heating appliances.

Do not use a damaged power 

Do not direct airflow directly at 
room occupants.

Always install circuit breaker 
and a dedicated power circuit.

Do not open the unit during 
operation.

Do not disassemble, modify, 
or drill holes into the air 
conditioner.

!

!

!

!

!

WARNING

! !

!

! !

!

cord.

Do not use the power cord near flammable gas 
or combustibles, such as gasoline, benzene, 
thinner, etc.

!

!

!

!

!

WARNING

SAFETY PRECAUTIONS

2

Summary of Contents for 2PATWH12000



























Reviews: