background image

Assembly & Operation Manual

 

Indication on 

Operating 

mode 

Operating signal 

RC-panel 

Turnstile status 

Post 

“One of the 

passage 

directions is 

open”

 

The low level on the 
contact 
corresponding to the 
passage direction, 
the high level on the 
other contacts. 

The green 
indicator of the 
chosen 
direction 

“Left” 

(

“Right”) 

is on. 

Green arrow in the 
chosen passage 
direction and green 
line pictograms are 
on. 

The turnstile is unlocked 
in the set direction. 

“Both 

passage 

directions 
are open”

 

The low level on 
contacts 

L

 and 

R

high level on 

“ST” 

contact

.

 

Both green 
indicators “Left” 
and “Right” are 
on.  

Green arrows for both 
passage directions 
and green line 
pictograms are on. 

The turnstile is unlocked 
in both directions. 

 

Note: 

For ACS outputs: 

 

High level — contacts of the output relay are open or the output transistor is closed. 

 

Low level — contacts of the output relay are closed or the output transistor is open. 

9.4  Actions in emergency  

In emergency situations (for example, in the event of power supply failure), the turnstile passage 
area can be used as an additional emergency exit. 

It is possible to turn the turnstile into 

Fire Alarm

 mode from the emergency unblocking device (fire 

alarm device, emergency button, etc.). In this mode, the turnstile barrier arm falls down (takes a 
vertical position) allowing the free passage in both directions, LED display shows the green (for 
1.25 sec) and red (for 0.25 sec) indicators, control commands from other devices and software are 
ignored (Sect. 5.3.2). 

The barrier arm is set into vertical position at a power loss as well. 

 

Caution! 

For urgent evacuation of people from facilities in case of fire, natural calamities or other 
emergencies, the additional emergency exit should be provided. Such emergency exit can 
be arranged with 

BH-02 

automatic anti-panic rotary section. 

9.5  Troubleshooting 

Possible faults, which can be cleared by the users themselves, are listed in Table 7.  

Table 7. Possible faults and solutions 

Fault 

Possible cause 

Solutions 

At the power-up the 
turnstile doesn’t work, and 
there is no indication on 
the turnstile housing and 
the RC-panel. 

No supply voltage to control board.

Switch off the turnstile power 
supply, detach the turnstile 
housing with the display unit from 
the turnstile base. Check the 
power cable serviceability and 
reliability of its connection to the 

X1

 connector block on the control 

board. 

The turnstile is not 
controlled in one of the 
directions. The turnstile 
housing and RC-panel 
indication is on. 

The interface board does not 
receive a control signal for this 
direction. 

Switch off the turnstile power 
supply, detach the turnstile 
housing with the display unit from 
the turnstile base. Check the RC-
panel / WRC / ACS controller 
cable serviceability and reliability 
of its connection 

X2

 

connector 

block on the interface board. 

28 

Summary of Contents for TTR-10A Series



































Reviews:

Related manuals for TTR-10A Series