background image

TTR-10A electromechanical tripod turnstile  

 

Figure 14. Dimensions and installation procedure for the 

MT10.1 

mounting bracket 

b.  Installation procedure for the 

MT10.2

 mounting bracket (

TTR-10AK

 modification) (Fig. 15):  

  Mark and cut the holes in the wall for the anchors to fix the turnstile and cable duct to the 

cable entry area. Use the turnstile bracket as a template to mark the holes if necessary.  

  Use a level to check the horizontal position of the bracket when marking and installing.  

  Pull the cables through the rack and through the corresponding bracket hole. The cable 

outlet from the hole must be at least 30cm long.  

  Use at least four anchor bolts to fix the bracket to the wall. The bracket has eight holes for 

M8 anchor bolts and four holes for M12 anchor bolts.  

 

Note: 

It is not recommended to mount the turnstile on the wall without using a standard 
bracket. In this case, the barrier arms will cling to the mounting surface during rotation or 
abut against it. 

 

Figure 15. Dimensions and layout of holes on the wall for fixing the MT10.2 bracket 

21 

Summary of Contents for TTR-10A Series



































Reviews:

Related manuals for TTR-10A Series