Pepwave Surf 200 Page 5 User Manual Download

Page: 5 / 22

PePWave Surf Series User Manual

Page 5

3.2

Hardware Setup

3.2.1 Surf Indoor Series

Attach the provided antenna to the left most antenna connector

Connect the LAN port to the computer’s Ethernet port with an Ethernet cable.

Connect the end of the included power adapter to the power socket (labeled “DC 5V”)
on PePWave Surf.

Power on the power adaptor.

3.2.1

Surf Outdoor Series

Please follow the installation guide to set up AP 200/400-X, PolePoint 400-X, Surf 400-DX

3.3

LED Description

3.3.1 Surf Indoor Series

LED

Color

Status

Description

Green

Power is on

Power

Off

Power is off

Green

Solid

Received signal is Excellent, Very Good and Good

Green

Blinking

Received signal is Low

Amber

Blinking

Received signal is Very Low

Amber

Solid

No wireless signal is detected

Status

Off

Booting up / Upgrading firmware

Green

Ethernet is connected

Green

Blinking

Sending/Receiving data

LAN

Off

Ethernet is not connected

Summary of Contents for Surf 200























Search results

Summary of Contents for Surf 200

Reviews:

Related manuals for Surf 200

Brands by name

Popular brands

Pepwave Surf 200, User Manual

Search results

Summary of Contents for Surf 200

Reviews:

Related manuals for Surf 200

Brands by name

Popular brands