Pepwave CarFi 200 User Manual Download Page 20 | Manualshive

Page: 20 / 27

background image

PePWave Surf/Mesh Connector/CarFi Series User Manual

Page 20

Important Note:

In the

Wireless Settings

section, if

Authentication

is set to either

802.1x with dynamic

WEP key

or

WPA/WPA2-Enterprise

, then the

Configure Automatically

option of the

Access Point Configuration becomes unavailable, because the Integrated Home Wi-Fi Access

Point functionality currently does not support authentication via the 802.1x with dynamic

WEP key and WPA/WPA2-Enterprise methods.

Illustration 5: Automatic Access Point Configuration is unavailable with 802.1 with

Dynamic WEP Key Authentication

«
...
18
19
20
21
22
...
»

Summary of Contents for CarFi 200




























Reviews:

No comments

Related manuals for CarFi 200

Inverter Power Cable Kit

Brand: Tripp Lite Pages: 2

Brand: Keysight Pages: 2

Brand: TE Connectivity Pages: 11

Venduct Duo Solar Series

Brand: KLOBER Pages: 2

Brand: CommScope Pages: 43

PRO SPLITTER 2 DS 20

Brand: Klark Teknik Pages: 3

Vitality SMARTCABLE

Brand: NEMECHEK TECHNOLOGIES Pages: 10

Brand: Optic Network Technology Pages: 3

Brand: E1DT Pages: 36

Brand: RADEMACHER Pages: 2

Brand: Farnell Pages: 11

Brand: Farnell Pages: 11

CABLINE-VS II PLUG

Brand: I-PEX Pages: 16

Brand: Olympus Pages: 76

SH160DIN-160DIN-2A

Brand: National Instruments Pages: 32

SYSTIMAX 360 iPatch 360G2-iP-32-MPO-SD-KIT-5PK

Brand: CommScope Pages: 19

Brand: Harmopool Pages: 2

Brand: Watts Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands