Pentair t29 Instruction Manual Download Page 19

© 2015 Pentair Equipment Protection

89104464

- 19 -

A.  An RMA # will be issued by our Product Return Department in Anoka, MN at 763-422-2211. Buyer 

should have following information available at time of RMA request:
1.  Complete Model Number, Serial Number and description of damaged unit being returned.

2.  Original Buyer Purchase Order number and date product was received by Buyer.

3.  Quantity to be returned and a brief description of failure for each unit, if different.

4.  Contact information of Buyer that must include: name of company, billing and shipping address, 

phone, number, fax number, freight carrier and the name and phone number of a Buyer contact 

who can elaborate on the claimed defect in detail.

5.  Buyer must provide a Repair Purchase Order number for both warranty and out of warranty 

repairs. The PO will not exceed 50% of a new unit. Buyer will be notified of repair charges that 

exceed approved PO amount.

B.  All returns to Pentair Equipment Protection must be securely packed, using original cartons if 

possible. All returns must have the RMA number visible on the outside of the carton. Pentair 

Equipment Protection is not responsible for material damaged in transit. Any refrigerant-bearing 

Goods must be shipped upright for return.

C.  Shipping cost for all non-warranty repairs is the responsibility of the sender and must be shipped 

prepaid. Shipping costs for all warranty related repairs will be covered by Pentair Equipment 

Protection provided the goods are returned using a Pentair Equipment Protection approved carrier. 

If after diagnoses the product is determined by Pentair Equipment Protection not be covered under 

warranty, Buyer will be responsible for all shipping charges and will be billed accordingly.

D.  Non-warranty repairs are subject to a $105 minimum analysis fee. If approval is not received within 

30 days, material will be scrapped and all shipping expenses and corresponding analysis fees will be 

billed to Buyer.

E.  At Buyer’s request, Failure Analysis can be provided by Pentair Equipment Protection for warrantable 

goods at no charge. Failure analysis for non-warranty repairs are subject to a $150 per hour 

Engineering charge plus any other incurred testing costs.

F.  All returned merchandise must be sent to the following address: Pentair Equipment Protection, 2100 

Hoffman Way, Anoka, MN 55303-1745.

G.  Credit for accepted returns shall be at the original selling price or the current selling price, whichever 

is lower, less the restocking charge indicated as follows:
1.  Within 60 days of invoice date - 20% of applicable selling price.

2.  Within 61-120 days of invoice date - 30% of applicable selling price.

3.  Within 121-180 days of invoice date - 40% of applicable selling price.

4.  Beyond 180 days - subject to individual review by Pentair Equipment Protection.
If product being returned for credit requires repair or modification, the cost of any labor or material 

necessary to bring product into saleable condition will be deducted from credit. Buyer may not take credit 

against returns without prior written Pentair Equipment Protection approval.

LIMITATION OF LIABILITY

PENTAIR EQUIPMENT PROTECTION WILL NOT BE LIABLE UNDER ANY CIRCUMSTANCES FOR ANY 

INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, INCLUDING WITHOUT LIMITATION ANY LOST 

PROFITS OR LABOR COSTS, ARISING FROM THE SALE, USE OR INSTALLATION OF THE GOODS, FROM 

THE GOODS BEING INCORPORATED INTO OR BECOMING A COMPONENT OF ANOTHER PRODUCT, 

FROM ANY BREACH OF THIS AGREEMENT OR FROM ANY OTHER CAUSE WHATSOEVER, WHETHER 

BASED ON WARRANTY (EXPRESSED OR IMPLIED) OR OTHERWISE BASED ON CONTRACT, OR ON TORT 

OR OTHER THEORY OF LIABILITY, AND REGARDLESS OF ANY ADVICE OR REPRESENTATIONS THAT 

MAY HAVE BEEN RENDERED BY PENTAIR EQUIPMENT PROTECTION CONCERNING THE SALE, USE OR 

INSTALLATION OF THE GOODS.

Summary of Contents for t29





















Reviews: