Pentair SandShark Installation & User Manual Download Page 18

SANDSHARK

 Automatic Vacuum Pool Cleaner Installation & User’s Guide

14

TERMS AND CONDITIONS APPLICABLE IN AUSTRALIA AND NEW ZEALAND 

Pentair warrants that, subject to the full terms and conditions included with the product, when used for 
the purpose for which it was designed, it will be free of material and manufacturing defects at the time 
of the original purchase. Any defects found in the products should be reported as soon as the fault is 
discovered.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are 
entitled to a replacement or refund for a major failure and for compensation for any other reasonably 
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail 
to be of acceptable quality and the failure does not amount to a major failure.

YOU MUST CAREFULLY READ THE INSTRUCTIONS  

SUPPLIED PRIOR TO USING ANY PENTAIR PRODUCT.

2-YEAR WARRANTY

Pentair warrants the product to be free from defects in material and/or workmanship for a period 

of 2-years, from the original purchase date. If a unit is deemed to be defective in material and/or 

workmanship, subject to the full terms and conditions included with the product, Pentair will provide a 

complete replacement head or repair parts as Pentair deems suitable.

What the Warranty Does Not Cover:

1.  Wear and Tear – The SandShark

 cleaner is designed with all components made of materials 

selected for maximum performance and durability. However there is expected wear and tear of 

certain components, which is normal. For example; foot pad, drive shafts, oscillator and gears will 

all degrade when operated with additional use or in harsher chemical environments than intended. 

For these components, it is expected the user replaces as frequently as is necessary. Contact your 

Pentair retailer for replacement parts.

2.  Physical Damage – Warranty is not provided for physical damage caused to the SandShark

 unit as 

a result of lack of care in handling or of mis-use. The SandShark

 cleaner is not a toy and should not 

be operated or played with by children. The cleaner should not be operated with people in the pool. 

Any damage that occurs to the cleaner in the pool as a result of obstacles or obstructions will not be 

covered by warranty.

3.  Pool Chemistry – Warranty is not provided for damage or wear which is the result of poor pool 

chemistry. Pool chemistry should be maintained within limits below and the cleaner should be 

removed from the pool during shock treatments.

  Chlorine: 1-4ppm (2-3ppm ideal)

  pH: 7.2-7.8 (7.4-7.6 ideal)

  Total Alkalinity: 60-180ppm (80-100ppm ideal)

  Calcium Hardness: 150-500ppm (200-400ppm ideal)

  Heavy Metals (Ag, Cu): None
4.  Incorrect Operation – Warranty is not provided for damage or wear which is the result of operation 

not in accordance with the instructions provided.

PLEASE REFER TO THE “PENTAIR WARRANTY TERMS AND CONDITIONS” DOCUMENT  

(INCLUDED WITH THE PRODUCT) FOR FULL WARRANTY TERMS AND CONDITIONS

WARRANTY INFORMATION

Summary of Contents for SandShark





















Reviews: