background image

SANDSHARK

 Automatic Vacuum Pool Cleaner Installation & User’s Guide

10

MAINTENANCE

1.  With a screwdriver, carefully work the rubber vacuum pad 

down over the lip of the Outer Housing, (see Figure 18).

2.  Lift the Outer Housing straight up off of the chassis.  

(see Figure 19).

3.  Squeeze and pull the Sprocket Clips to release the Drive 

Shaft Assembly and Center Sprocket, (see Figure 20).

4.  Pull the Oscillator Straight out from the bottom of the 

Outer Housing. Be careful not to lose the Sliding Seals, 
(see Figure 21).

5.  Squeeze the latching tabs and pull up on the Swivel 

Housing and Swivel. The assembly will come up, releasing 
the Swivel Sprocket. Squeeze the latching tabs to remove 
the Clutch Clip, (see Figure 22).

6.  Remove the Shaft Plug with the stainless steel shaft and 

the Large Steering Drive Assembly, (see Figure 23).

7.  Remove the Oscillator Sleeve, releasing the Oscillator 

Sleeve Bushing and the Clutch assembly, (see Figure 24).

8.  If you need to replace the bumper, turn the housing/

bumper assembly upside down and remove the two flex 
snaps holding the bumper to the housing, (see Figures 
25 & 26). Use a piece of ½ in. (inside diameter) PVC pipe 
to slide over the flex snap ends to squeeze the flex snaps 
together so they can be slid out of the housing. Use a pair 
of pliers to pop the flex snaps off of the bumper.

Disassembly

Reassembly

To reassemble the SandShark

, reverse the steps above.

NOTE:

 The notch on the center disk of the Large Steering 

Drive Assembly must be down (as shown in Figure 25) for 
assembly.

Figure 18

Figure 19

Figure 20

Figure 21

Figure 22

Figure 23

Figure 26

Figure 25

Figure 24

Figure 27

Use a 
pair of 
Pliers 
to pull 
the Flex 
Snaps 
from the 
Bumper.

Use a piece 
of ½ in. PVC 
pipe (inside 
diameter)
to push the 
Flex Snaps
out of the 
Housing.

Summary of Contents for SandShark





















Reviews: