background image

ii

 

REBEL™ Suction Side Pool Cleaner Installation and User’s Guide

ii

IMPORTANT WARNING AND SAFETY INSTRUCTIONS 

Important Notice:

 

Attention Installer: 

This guide contains important information 

about  the  installation,  operation  and  safe  use  of  this  product. 

This information should be given to the owner and/or operator of 

this equipment after installation of the pool cleaner.

Attention  User: 

This  manual  contains  important  information 

that will help you in operating and maintaining this pool cleaner. 

Please retain it for future reference.  Consult  Pentair  with  any 

questions regarding this equipment.

                      Before installing this product, read and 

follow all warning notices and instructions which are included. 

Failure to follow safety warnings and instructions can result 

in severe injury, death, or property damage.  Call 1300 137 344 

for additional free copies of these instructions.

Consumer Information and Safety

This  pool  cleaner  is  designed  and  manufactured  to  provide 

many  years  of  safe  and  reliable  service  when  installed, 

operated  and  maintained  according to the information in this 

manual. Throughout the manual, safety warnings  and  cautions 

are identified by the 

 

“       ” symbol. Be sure to read and comply 

with all of the warnings and cautions.

General Installation Information

Pre-Installation Check List

Before  installing  your  cleaner,  review  and  understand  all 

warnings  and  safety  information  in  this  guide.  Failure  to 

follow  these  instructions  or  improper  installation  of  the 

cleaner can result in damage to the pool finish or the vinyl liner, 

Pentair  Water  Pool  and  Spa,  Inc.  disclaims  any  liability  for 

repairs  or  replacement  to  any  of  these  structures  or 

components of the customer’s pool.

Before installing the cleaner in a vinyl liner pool:

Check  liner  closely  for  signs  of  deterioration  or  damage 

from  age,  chemicals, pool wall damage, etc. If any damage is 

found, have a qualified pool professional make all the necessary 

repairs.  Also,  if  there  are  stones, roots,  etc.,  under  the  liner, 

remove them before installing the cleaner.

Before installing the cleaner in a gunite pool or a pool that is 

partially or completely tiled:

Repair loose tiles and tighten any loose light rings.

Before installing the cleaner, clean your filter system:

Make sure you have cleaned the filter, including backwashing, 

rinsing,  and emptying all baskets. A clean system is necessary 

for proper cleaner operation and coverage.

Before installing the cleaner, understand cleaner coverage:

The  cleaner  is  designed  to  rid  your  pool  of  debris  in 

approximately  4-6  hours.  Less  time  could  be  needed, 

depending  on  the  pool  size.  The  cleaner was not designed to 

automatically clean steps or swimouts or to work under a solar 

cover. It was also not designed to do initial cleanup for a new 

pool or when opening your pool for the season.

AFTER installing the cleaner, make sure the cleaner is 

operating correctly:

The  cleaner  may  need  some  minor  adjustments  to  make 

sure  it  is  operating  properly  so  there  is  no  damage  to  the 

pool  finish.  Certain  vinyl  liner  patterns  are  particularly 

susceptible  to  surface  wear,  pattern  removal, ink rubbing off 

of,  or  serious  scratches  to  the  pattern  caused  by  objects 

coming  into  contact  with  the  vinyl  surface,  including 

automatic  pool  cleaners.  Pentair  Water  Pool  and  Spa,  Inc.  is 

not responsible for any pattern removal, abrasions or markings 

on vinyl liners.

HAZARDOUS SUCTION.

 

Do not play with cleaner or hose or apply to 

body. Can trap and tear hair or body parts. 

Hose can trip or entangle swimmers which 

could result in drowning. 

SUCTION  ENTRAPMENT,  INJURY,  AND 

DROWNING HAZARD.

 If your pool has a 

dedicated suction port (“vac port”) for 

vacuuming or for an  automatic pool cleaner, 

it must be covered when  not in use. A spring 

loaded safety cover (a “vac port fitting”) is 

included with your cleaner. Install it on the 

suction port to prevent entrapment and injury. 

If the cover provided does not fit, purchase one 

that does from your local pool store and install 

it instead. The cover should conform to IAPMO 

SPS4-99A.

Stop  pump

  before  attempting  to  clean 

unit.  Do  not  allow  swimmers  in  pool  while 

pool cleaner is operating.

To reduce the risk of injury, do not let 

children use or play with pool cleaner.

Do  not  allow  swimmers  in  the  pool  while  pool 

cleaner is operating. Hose can trip or entangle 

swimmers which could result in drowning.

Moving parts may injure hands or fingers. 

Stop pump before attempting to clean out 

pool cleaner head.

Warnings and safety instructions for Pentair Water Pool and Spa, 

Inc. pumps and other related products are available at:

http://www.pentairpool.com/pool-owner/safety-warnings/

 or call

(800) 831-7133 for additional free copies of these instructions.
Please refer to 

http://www.pentairpool.com/pool-owner/

safetywarnings/

 for warning and safety instructions related to 

this product.

IMPORTANT WARNING & SAFETY INSTRUCTIONS

POOLSHARK

 Automatic Vacuum Pool Cleaner Installation & User’s Guide

Summary of Contents for POOLSHARK





















Reviews: