Pentair Evolio 255 10 Installer Manual Download | Manualshive

Page: 12 / 90

background image

Installer manual Evolio 255 740-760 - Safety

12 / 90

Ref. MKT-IM-037 / D - 25.10.2021

2.3

Hazards

All the safety and protection instructions contained in this document must be observed in order to
avoid temporary or permanent injury, damage to property or environmental pollution.

At the same time, any other legal regulations, accident prevention and environmental protection
measures, as well as any recognized technical regulations relating to appropriate and risk-free
methods of working which apply in the country and place of use of the device must be adhered to.

Any non-observation of the safety and protection rules, as well as any existing legal and technical
regulations, will result in a risk of temporary or permanent injury, damage to property or
environmental pollution.

2.3.1

Personnel

CAUTION

Risk of injury due to improper handling!

Only qualified and professional personnel, based on their training, experience and
instruction as well as their knowledge of the regulations, the safety rules and operations
performed, are authorized to carry out necessary work.

WARNING

Appliance

This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensor or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved.

WARNING

Children

Children shall not play with the appliance.

«
...
10
11
12
13
14
...
»

Summary of Contents for Evolio 255 10



























































































Reviews:

No comments

Related manuals for Evolio 255 10

Formula Pro Advanced

Brand: Baby Brezza Pages: 8

Brand: Lancaster Water Treatment Pages: 14

Brand: aidapt Pages: 2

Maestrale Jolly 12

Brand: Bras Pages: 32

Brand: clage Pages: 28

Brand: Talent Pages: 28

Brand: Hampton Research Pages: 2

Brand: STIEBEL ELTRON Pages: 56

EWTLA16*1E Series

Brand: Elkay Pages: 4

Brand: Millipore Pages: 2

Brand: Hyco Pages: 2

Brand: Elkay Pages: 8

Brand: Vinotemp Pages: 20

SmartNODE SMN-823W

Brand: Cadi Pages: 16

Brand: STIEBEL ELTRON Pages: 20

Brand: Servend Pages: 34

Brand: CENTRAL RESTAURANT PRODUCTS Pages: 9

Brand: Bobrick Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands