PENSOTTI PCC 34 H Cleaning Procedure Download Page 29 | Manualshive

Page: 29 / 30

background image

Version 1

29

Diverter Valve Lubrication

33. Lubricate the diverter valve.

Remove the right-hand side panel. Using a spray can of PTFE lubricant* with a precision spray

straw attached, spray a small amount of lubricant directly onto the drive shaft of the diverter valve. Wipe away any excess lubricant.
Failure to lubricate the diverter will result in premature failure and may void the warranty of this item. Reinstall the side panel upon
completion.

*’

Superlube

’ is an example

Warning

Read and follow all safety precautions on the label of lubricant

Space Between Motor and Valve Assembly

Drive Shaft (Brass)

«
...
27
28
29
30
»

Summary of Contents for PCC 34 H































Reviews:

No comments

Related manuals for PCC 34 H

Brand: Daikin Pages: 44

Brand: Watts Pages: 62

Vitodens 050-W BP JD

Brand: Viessmann Pages: 92

microGENUS 23 MFFI

Brand: Ariston Pages: 28

Brand: Riello Pages: 28

Brand: CHAFFOTEAUX Pages: 16

Brand: Pereko Pages: 24

Brand: Camus Hydronics Pages: 82

Brand: Radiant Pages: 58

Brand: Vollrath Pages: 6

VICTORY II VHS Series

Brand: Slant/Fin Pages: 1

Brand: Slant/Fin Pages: 1

Brand: Slant/Fin Pages: 12

VICTORY VSPH/NDV-120

Brand: Slant/Fin Pages: 24

Brand: kunzel Pages: 28

BRAVA One HE 25

Brand: Sime Pages: 108

Brand: Atmos Pages: 40

Brand: Truma Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands