manualshive.com logo in svg

PenBits BACHMANN CLASS 24, Assembly Instructions Manual, Page: 50 / 52

Share
Download
PenBits BACHMANN CLASS 24 Assembly Instructions Manual Download Page 50

Pickups  are  bent  up  from  0.011"  phosphor
bronze  wire  as  shown.  The  wire  coils  are

formed  of  six  turns  around the  shank  of  a
0.7mm  drill,  finished  so  that  the  pick  ups
themselves are preloaded below their operating
position  by  about  1mm.  The  wires  are  tinned
and  then  soldered  to  the  copper-clad  with  a
touch of the iron …

…  with  the  feed  wires  tinned  and  soldered
on  in  turn,  resin-cored  solder  being  used

throughout.

The  feed  wires  from  the  pickups  back  to
the  loco  PCB  are  attached  to  the bogie

bolsters  by  threading  them  through  the  holes
near  the  top  of  each  bolster.  This  allows  the
rout e of  the  wires  between  the  bolster  and
drive  unit  to  be  set  and  then  to  remain
undisturbed when the wires are  routed  through
the chassis block during the fitting of the bogie
to the loco.

Pickups and Power

50/51

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

Summary of Contents for BACHMANN CLASS 24





















































Reviews:

No comments