PEMTECH PT750 Series W Operator'S Manual Download Page 14 | Manualshive

Page: 14 / 17

background image

Alarm Condition

If the sensor goes into alarm the sensor data reading starts flashing in red. Also the bold alarm
messages starts flashing on the status bar at the bottom of the screen.

Once the alarm clears the red flashing messages are cleared. However, the sensor location tag
will still be flashing. This feature is useful if any detector went into alarm and then cleared after
sometime. With the tag flashing the user can determine which detector went into alarm state.
This flashing tag can be reset or cleared by pressing the RESET button on the status bar.

«
...
12
13
14
15
16
...
»

Summary of Contents for PT750 Series W


















Reviews:

No comments

Related manuals for PT750 Series W

Brand: Radio Shack Pages: 52

Brand: Ebyte Pages: 34

Brand: YASKAWA Pages: 61

Brand: nvent Pages: 6

Brand: Smart Vision Pages: 5

Brand: Teledyne Pages: 47

Brand: Western Co Pages: 14

Brand: Yoshitake Pages: 18

Brand: Xantech Pages: 7

Brand: Chamberlain Pages: 1

Brand: Zeversolar Pages: 8

Brand: ECUE Pages: 39

Brand: Regada Pages: 41

Brand: Powtran Pages: 36

X-Series X-SMS V2

Brand: IDS Pages: 2

Brand: Larco Pages: 15

BMS NUV100-CI-12

Brand: Nuvation Pages: 41

Brand: Quectel Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands