background image

4

SAFETY INSTRUCTIONS

•  The HELION hedge trimmer is a professional tool reserved exclusively for trimming bushes and hedges.

•  PELLENC S.A. declines all responsibility in case of damage caused by improper use and use other than 

for which it is intended.

•  PELLENC S.A. also declines all responsibility in case of damage caused by the use of non-genuine parts 

or accessories.

GENERAL SAFETY INSTRUCTIONS FOR THE TOOL

CAUTION Read all the safety measures and all the instructions.

Retain all the safety measures and instructions for later reading.

Work area safety

a.  Keep the work area clean and well lit. 

b. 

Do not use electric tools in an explosive atmosphere, for example in the presence of flammable 

liquids, gases or dust. 

c.  Keep children and persons present away when using the tool. 

Electrical safety

a.  The plugs of the electric tool must be adapted to the base. Never modify the plug in any way 

whatsoever. Do not use adaptors with grounded tools. 

b.  Avoid any body contact with grounded surfaces such as pipes, radiators, cookers and refrigerators. 

c.  Do not expose tools to rain or damp conditions. 

d.  Do not misuse the power cord. Never use the power cord to carry, pull or disconnect the tool. Keep 

the power lead away from heat, lubricant, sharp edges or moving parts. 

e.  When using a tool outdoors, use an extension adapted to outdoor use. 

f.  If you must use a tool in a damp place, use power supply protected by a residual current device 

(RCD). 

Personal safety

a.  Remain vigilant, watch what you are doing and use common sense when using the tool. Do not use a 

tool if you are tired or under the influence of drugs, alcohol or medication. 

b.  Wear safety equipment. Always wear eye protection.

c.  Avoid any untimely starting of the device. Make sure the switch is in the off position before connecting 

the tool to the mains and/or battery pack, picking it up or carrying it. 

d.  Remove any adjustment key before starting the tool. 

e.  Do not rush. Adopt a suitable position and remain balanced at all times.

f.  Wear appropriate clothing. Do not wear loose clothing or jewellery.

g.  Keep hair, clothing and gloves away from moving parts. 

h.  If systems are provided to connect dust extraction and recovery equipment, make sure these 

systems are connected and properly used.

This appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given 

supervision or preliminary instructions by a person responsible for their safety.

KEEP THESE INSTRUCTIONS

Summary of Contents for HELION POLE TELESCOPIC























Reviews: