pellenc FIXION 2 Operating Instructions Manual Download

Page: 44 / 48

TYING MACHINE FIXION 2

29_133084-G

11. EC STATEMENT OF COMPLIANCE

11.1. "EC" DECLARATION OF CONFORMITY: FIXION 2

MANUFACTURER/ENTITY AUTHORISED TO COMPILE THE

TECHNICAL FILE

PELLENC

ADDRESS

Quartier Notre-Dame - 84120 Pertuis

(France)

We hereby declare that the machine referred to below as:

GENERIC DENOMINATION

Tying machine

FUNCTION

Intended to attach vine shoots

COMMERCIAL NAME

FIXION 2

TYPE

FIXION 2

MODEL

FIXION 2

SERIAL NO.

29V00001 - 29V49999 29W00001 - 29W49999 29X00001 - 29X49999

Complies with the relevant provisions of the machinery directive 2006/42/EC.

Complies with the provisions of the following European Directives:

• 2014/30/EU EMC Directive; 2011/65/EU ROHS Directive; 2014/53/EU RED Directive; 2006/66/EC Batteries &

Accumulators Directive; 1907/2006 REACH Regulation; 2012/19/EU WEEE Directive

The following harmonised European standards have been used in part or in full:

• EN 62841-1:2015 ; EN 55014-1:2017 ; EN 55014-2:2015 ; EN 62133-2:2017 ; EN 61000-3-2:2019 ; EN

61000-3-3:2013+A1:2019

SIGNED IN PERTUIS, DATED 22/06/2021
JEAN-MARC GIALIS
CHIEF EXECUTIVE OFFICER

Summary of Contents for FIXION 2

















































Search results

Summary of Contents for FIXION 2

Reviews:

Related manuals for FIXION 2

Brands by name

Popular brands

pellenc FIXION 2, Operating Instructions Manual

Search results

Summary of Contents for FIXION 2

Reviews:

Related manuals for FIXION 2

Brands by name

Popular brands