background image

INSTALLATION INSTRUCTION -  

INSTRUCCIONES DE INSTALACIÓN  

FOR SQUARE DESIGN BAY AND BOW WINDOW 

WITH SEAT BOARD 

Part Number: 81470102

© 2009 Pella Corporation

Read these instructions thoroughly before performing any steps.

Note: These instructions may be used for Square Design Pella Bay and Bow windows that 
have a head and seat board. Support cables are installed in factory assembled bay and bow 
combinations.

Caution: The factory-installed support cables must be attached to members capable of 
supporting 1,300 lbs. If the members are not capable of supporting 1,300 lbs., knee braces 
must be used in addition to the cables. Bay and bow units are not intended to support any 
roof structure. Consult an architect, engineer or construction professional if the ability of the 
members to support the bay or bow is not known.

Installation Instructions for Typical Wood Frame Construction.
These instructions were developed and tested for use with typical wood frame wall 
construction in a wall system designed to manage water. 

These instructions are not to be 

used with any other construction method.

 Installation instructions for use with other 

construction methods, multiple units or other bow and bay windows, may be obtained 
from Pella Corporation, a local Pella retailer, or by visiting http://www.pella.com. Building 
designs, construction methods, building materials, and site conditions unique to your project 
may require an installation method different from these instructions and additional care. 
Determining the appropriate installation method is the responsibility of you, your architect, 
or construction professional. 

Always read the Pella

®

 Limited Warranty before purchasing or installing Pella products. By 

installing this product, you are acknowledging that this Limited Warranty is part of the terms of the 
sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella 
product warranty. See Limited Warranty for complete details at http://warranty.pella.com.

Cable clamps

Flashing tape #1 

Flashing tape #2 

Jamb covers

Knee braces

Head frame

expander

(2-1/2" Wide)

Lea las instrucciones en español en el reverso.

Summary of Contents for 81470102













Reviews: