5
Safety instructions
•
Read and follow the instructions in this manual
before using the lift. Make sure that the work
area has a reassuring and sufficient light. Do
not use the lift if you are tired or under the influ
-
ence of drugs, alcohol or medication.
•
Clean regularly. Dust and debris in a workplace
increase the risk of accident, fire and explosion
•
Only trained personnel may use the lifting
equipment. The lift may only be used for lifting
according to the instructions in this manual.
•
Never exceed the maximum lifting capacity of
the lift. Overloading can damage the lift and
lead to an accident.
•
The lift may only be used on hard, flat surfaces
that can withstand the load to which it will be
subjected. If use is made on another type of
surface, the lift will be unstable and there is a
risk that the lifted load may fall down.
•
The lift may only be used for motor lifting.
•
Do not exceed the specified maximum load of
the lift.
•
Never let children take care of or play with the
lift.
•
Keep finger, hands and feet away from lifting
arms or other moving parts. Failure to follow
these warnings and safety instructions may
result in damage to the lift or, in the worst case,
fatal injury.
How to use: lift
1. Stäng utsläppsventilen genom att skruva hand-
taget medurs. Använd inte överdriven kraft.
2. Fäst med lämplig utrustning föremålet på lyf-
tens krok.
3. Pumpa med handtaget upp och ner. Kon-
trollera upphängningen av lasten, om den är
OK fortsätt att pumpa till önskad höjd. Placera
godkända pallbockar under upp-lyft last innan
arbete utförs.
Lower
NOTE! Always lower the load slowly.
1. Open the discharge valve by screwing the
handle counterclockwise. NOTE! Do not open
the discharge valve more than one turn.
2. Unload the lift as soon as possible by placing
the load on an approved trolley or similar equip-
ment.
Teknisk specifikation
Maintenance
Top up with oil.
1. Set the pump unit vertically, open the valve,
place the pump handle lowered.
2. Push the plunger down to the bottom.
3. Remove the rubber oil plug in the middle of the
pump unit.
4. The oil level should be at the bottom of
5.
the filling hole. If necessary - top up
6. hydraulic oil intended for jacks. Ventilate the
system by gently raising and lowering the lift fl
your times.
7. Replace the oil plug.
8. Lubricate the joints regularly with a thin oil.
Lifting capacity
Max 2000 Kg
Lifting height
2360mm
Beam
1050 ~1590mm
Weight
92 Kg
Aeration of the system
Sometimes it happens that air bubbles remain
inside the piston, which leads to a decrease in the
effect. Then ventilate as follows:
1. Open the discharge valve and remove the oil
plug.
2.
Pump quickly with the lever fl your times to
force the air out.
3. Close the discharge valve and replace the oil
plug. The lift should now work normally. If not,
repeat the aeration.
Contact
PELA Tools
Solängsvägen 13
SE-513 70 Borås
Phone: 033-202650
E-mail: [email protected]
Environmental protection /
Scrapping
Recycle any unwanted material,
do not throw it in the household
rubbish. All machines, accessories
and packaging must be sorted and left
at a recycling center and disposed
of in an environmentally friendly
manner.
Important!
These operating instructions must be considered
as part of the lift and must always be kept with
them. If the lift is sold, the operating instructions
must be handed over to the new owner. Always
keep the operating instructions in a place that is
easily accessible to the user and ensure that they
are kept in good condition. The operating instruc-
tions contain important information concerning
your safety. Carefully follow the safety instructions
to avoid the risk of personal injury and damage to
