96-500 Sochaczew, ul. 15-go Sierpnia 33a
NIP: 837-135-72-55, Regon: 140146548
tel./fax +48 46 862 34 88, tel. 48 513 153 944
Credit Agricole Bank Polska S.A.
tel./fax +48 22 379 79 44 www.peiter.pl, [email protected]
19 1940 1076 5239 5305 0000 0000
www.peiter.pl
96-500 Sochaczew, ul. 15-go Sierpnia 33a
NIP: 837-135-72-55, Regon: 140146548
tel./fax +48 46 862 34 88, tel. 48 513 153 944
Credit Agricole Bank Polska S.A.
tel./fax +48 22 379 79 44 www.peiter.pl, [email protected]
19 1940 1076 5239 5305 0000 0000
www.peiter.pl
7.
Now the ArtMatic LED will change the flash mode (more fast) for a reconfirmation of the correct code
learning. This step may take some seconds.
8.
At this moment, press the ArtMatic button when you want to store the code and retain pressed until the
ArtMatic LED switches off.
9.
Activate now the
D.O.R.
procedure to insert the new remote control on the receiver.
V2 433 - 868 - D.O.R.
1.
While pressing the button 1 of the ArtMatic, at the same time press 4 times the 2 button.
2.
Release both buttons. Now the ArtMatic LED will emit a short flash every 2 seconds.
3.
Place the original remote control to be programmed in front of the ArtMatic, at about 5 cm of distance
(as shown in the picture).
4.
Press and retain pressed the button to be programmed of the original remote control, till the LED will
switch on as a fix light; now release the button.
5.
The ArtMatic LED will emit a short flash every 2 seconds”. This alert informs the user that, to duplicate
the remote control, it is necessary to emit the SEED CODE to realize the copy.
6.
Transmit now the SEED CODE of the V2 original remote control pressing at the same time 1 and 2
buttons.
7.
Now the ArtMatic LED will change the flash mode (more fast). This step may take some seconds.
8.
At this moment, press the ArtMatic button when you want to store the code and retain pressed until the
ArtMatic LED switches off .
9.
Activate now the
D.O.R.
procedure to insert the new remote control on the receiver.
To activate the remote control on the receiver for models marked with D.O.R. proceed as below:
1.
First of all you must be closed to the automation.
2.
Press and retain pressed the programmed button during 10 seconds, when the LED start to flash,
release the button.
3.
Wait until the LED will turn off. The operation has been done, now you can use your new remote
control.
To activate on the receiver all the other models: Refer you to the instructions of the original model.
NOTE: THE SEED CODE OF THE ARTMATIC CAN BE EMITTED AS HERE BELOW:
1.
Press the buttons 1 and 2 simultaneously for 8 seconds and release them when the LED start to flash;
2.
While the LED is flashing press the button with the seed code needed.
ATTENTION!
Every kind of receiver can have the “radio-mode” disarmed. In this cases will be necessary
insert the new remotes controls with the “manual procedures”.
FAAC 433 - 868 / GENIUS 433 - 868
Attention: verify the programming remote control is a MASTER. Pressing whatever button, the LED
has to emit a double flash rather than to switch on as a fixed light.
1.
While pressing the button 1 of the ArtMatic, at the same time press 4 times the 2 button.
2.
Release both buttons. Now the ArtMatic LED will emit a short flash every 2 seconds.
