background image

     

 DIN NANO 3RK 

 

 

            

Chapter 4 

– Terms of guarantee 

                                                                                                                                                                                                                                                                                                                                                                                                                                         

 

Rev. 01-16

 

Page  8

 

 
 
 
 
 

TERMS OF THE GUARANTEE 

 

The NANO DIN electronic controls are guaranteed against all manufacturing defects for 24 months from the 
date in the production identification code. 
 
In the event of defects, the device must be returned properly packaged to our Site or authorised assistance 
centre after requesting and receiving the authorisation number for returning the product. 
 
The  Customer  has  the  right  to repair  the  defective  device  inclusive  of  manual  labour  and  spare  parts.  The 
Customer assumes sole responsibility for the expenses and the risks associated with transport. 
All  work  carried  out  under  the  terms  of  the  guarantee  does  not  renew  or  extend  the  duration  of  the 
guarantee. 
 
The guarantee does not cover: 

 

Damage attributable to tampering, negligence, carelessness or inadequate installation of the device. 

 

Installation,  use  or  maintenance  not  in  compliance  with  the  rules  and  instructions  provided  with  the 
device. 

 

Repairs carried out by unauthorised personnel. 

 

Damage attributable to natural causes like lightning, natural disasters, etc. 
In all the above cases, the customer pays for the cost of repair. 

 
Request  for  repairs  under  the  terms  of  the  guarantee  may  be  refused  if  the  device  has  been  modified  or 
converted. 
 
PEGO S.r.l. cannot assume responsibility for any loss of data or information, the cost of replacement goods 
or  services,  injury  to  people  or  animals,  loss  of  sales  or  earnings,  downtime,  and  any  direct,  indirect, 
accidental, pecuniary, collateral, punitive, special or consequential damage or loss caused in any way, within 
or  outside  the  scope  of  the  contract  or  due  to  negligence  or  other  responsibilities  associated  with  use  or 
installation of the product. 
 
The guarantee is terminated automatically in the event of poor operation attributable to tampering, collisions 
and  inadequate  installation.    It  is  obligatory  to  observe  all  the  rules  in  this  manual  and  the  operating 
conditions of the device. 
 
PEGO  S.r.l.  cannot  assume  any  responsibility  for  inaccuracies  in  this  manual  attributable  to  printing  or 
transcription errors. 
 
PEGO S.r.l. reserves the right to make changes to its products that it considers necessary or useful without 
affecting their essential characteristics. 
 
Each new release of the manuals for PEGO's products replaces all previous releases. 
 
Unless specified otherwise, the guarantee is governed by the rules in force and, in particular, article 1512 of 
the Italian Civil Code. 
 
All disputes are settled at the Court of Rovigo. 
 

4.1 

CHAPTER 4: TERMS OF THE GUARANTEE 

Summary of Contents for 200NDIN3RK

































Reviews: