Peg-Perego POLARIS TRAIL BOSS, Use And Care Manual

Page: 9 / 24

INITIAL BATTERY RECHARGE
BATTERY IS ALREADY INSTALLED IN VEHICLE.
Before riding, charge your battery for 18 hours to initiate them. Failure to do this can result in permanent battery damage.
• Turn the seat lock to the “unlock” position as shown in the diagram and lift the seat. NOTE: Seat has a “lock” and “unlock” position.
•
Battery is located in compartment located beneath seat. NOTE: Battery is secured into place with black plastic retainer and disposable cardboard. Battery
can be charged in or out of vehicle. To remove battery see steps 37 & 38.
• Plug the battery-charger into a household electrical outlet, following the instructions that come with the battery-charger. Connect plug B to battery-charger plug
C .
CAUTION :
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE
HAZARD.
1 • Lift both rear shock absorbers, and line them up with the openings in the chassis.
2 • To fasten the shock absorbers to the chassis, insert the pins into the top holes on the shocks, with the tabs turned vertically (see detail).
3 • Finish fastening the shock absorbers by placing the plastic tool on the pins and hammering the pins all the way in.
4 • Remove the protective caps from the ends of the front wheel axle.
5 • Slip a large washer onto the axle.
6 • Slip one of the two wheels onto the axle, taking care to place the tread in the direction shown in the figure.
7 • Slip a small washer and the nut onto the axle.
8 • Tighten the nut with the supplied wrench.
9 • Snap the nut cap into place, and repeat the operation on the other side of the vehicle, beginning from figure 8.
10 • Assemble the 2 parts of the front bumper with the 2 screws provided, as shown in the figure.
11 • Position the bumper on the front of the vehicle, inserting it and pressing down the upper side until it fits into the lower side.
12 • Secure the upper part of the bumper with the two screws provided.
13 • Secure the lower part of the bumper with another 2 screws.
14 • Attach the silver sticker to the chassis, as shown in the figure.
15 • Snap the taillight into place by inserting it from the top.
16 • Position the right handle on the rear of the vehicle, and secure it with the 2 screws provided. Repeat for the left handle. Please note: the two handles are different;
check them by looking on the inside.
17 • Fit the 2 screw covers onto the handle, putting the bottom part into the housing first (1) and then pressing down on the top part (2). Repeat for the other handle.
18 • Snap the toy gas tank cap into place.
19 • Assemble the handlebar/headlight unit as shown in the figure.
20 • Apply the reflective chrome decal as show in the figure.
21 • Attach the clear headlight lens.
22 • Slip the two hand guards onto the handlebars, lining up the holes in the hand guards with the holes in the handlebars.
23 • Fasten the hand guards with the two screws.
24 • Use a little liquid detergent to moisten the inside of the handgrips. Slip the handgrips onto the handlebars.
25 • Snap the handlebar into place on the vehicle. Attention: If the handlebar should happen to come loose, please see figures 39 & 40.
26 • Unscrew the screw and remove the glass from the control panels.
27 • Apply decal #22 before replacing the glass.
28 • Exclusive SmartPedal Technology™ feature allows for longer running times and more realistic driving. When accelerator is pressed completely down, forward
motion is activated. When pedal is released halfway, coasting action is engaged. Brake activates automatically when the child’s foot is removed from the pedal.
29 • GEAR SHIFT LEVER: The vehicle has three speeds. ATTENTION: When the vehicle is first removed from the packing, it only runs in first gear ( 1 ) and reverse ( R ). To
use the second gear ( 2 ), proceed as follows:
30 • Screw down the second gear unit, as shown in the following figure.
31 •
1-R : The second gear unit protrudes from the chassis, preventing the gearshift lever from moving down to the second gear. 1-2-R : The second gear unit is
completely screwed into the chassis, and the gearshift lever can be lowered.
BATTERY RECHARGE
WARNING :
WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE CARRIED OUT
BY ADULTS ONLY.
THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM THE VEHICLE.
32 • Disconnect the electrical system plug ( A ) from the battery plug ( B ) by pressing on the sides of the plugs.
33 • Plug the battery-charger into a household electrical outlet, following the instructions that come with the battery-charger. Connect plug B to battery-charger plug
C .
34 • After the battery has finished charging, disconnect the battery-charger from the electrical outlet, then disconnect plug C from plug B .
35 • Press plug B all the way into plug A , until it snaps into place. After finishing this operation, always remember to close and fasten the seat, using the safety screws.
36 • To replace the battery, lift the seat and open the cover on the battery compartment. Remove the battery and disconnect the plugs.
37 • Remove the plastic retainer by pressing in on the sides and sliding it over.
38 • Replace the battery and reconnect the plugs. NOTE: Be sure to also replace the retainer. Close the battery compartment and lock the seat.
To avoid your having to send the entire vehicle to the service center, we list instructions below for replacing some of the vehicle parts.
39 • HANDLEBAR: To replace the handlebar, open the seat and remove the battery. Slip your hand into the battery compartment and locate the steering lever.
40 • Press the two buttons on the steering lever to release the handlebars, while pulling the handlebar upwards and off the vehicle. NOTE: It takes two people to
remove the handlebar.
41 • GEAR SHIFT LEVER: To replace the interior gearshift lever unit, open the seat and remove the battery. Turn the vehicle on its side. Loosen the two screws on the
bottom of the vehicle, shown at points 1 and 2 in the figure. Using a pair of pliers, remove the stationary wire strip (3).
42 • Turn the vehicle upright, on its four wheels. Position the gear shift level in second gear (see figures 42 & 43) and loosen the screws that hold it in place. Remove the
gearshift lever.
43 • Slip your hand into the battery compartment and remove the interior gearshift lever unit.
ASSEMBLY INSTRUCTIONS
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
BATTERY RECHARGE
BATTERY REPLACEMENT
INSTALLING REPLACEMENT PARTS